similar to: Clipping on outbound calls via SIP/IAX

Is anyone else experiencing 404 errors on outbound dial with Broadvoice? I've followed the instructions posted by Broadvoice to configure sip.conf, and inbound calling works fine. Every time I try to dial out, I get a 404 "Not Found" error. Here are the relevant sections from my configs. sip.conf: context=broadvoice-in register =>

> -----Original Message----- > service is compatible with Asterisk). However, I have a question: can > more than one person make/receive a call at the same using one VoIP > line? > > If five people in the office all need to use their phones at the same > time, would I need five VoIP lines, or would I only need one > VoIP line? > Am I over-thinking this? No,

How do I solve the problem with between patterns: _1800 _1NXX I would like all numbers 1800, 1877 etc to go through iaxtel but all other numbers 1xxx via voipjet Example in my extension.conf I have: [iaxtel] exten => _1700NXXXXXX,1,Dial(IAX2/xxxx:xxxxx@iaxtel.com/${EXTEN}@iaxtel) exten => _1888NXXXXXX,1,Dial(IAX2/xxxx:xxxxx@iaxtel.com/${EXTEN}@iaxtel) exten =>

I am just now investigating Asterisk. Can Asterisk provide 6-10 party teleconferencing when configured properly?

Hi, I install CenOS 3.4, how import the gpg key ? Thx

I posted this question a while back, and I'm posting again in hopes that someone has some ideas. Sorry if you've already seen this. When dialing out using a SIP or IAX provider (Broadvoice, SimpleTelecom, VoicePulse Connect) I often find that after the call is answered the first few seconds of audio are cut off (i.e. I don't hear the called party). This usually results in the called

I have googled until blie in the face, WiKi'd until physically exhausted and searched through every Asterisk repository that I can find, all to no avail... No matter which version of SpanDSP I use, with which version of libtiff, Asterisk, ... I simply cannot send faxes. I can receive faxes *perfectly* (sending from standard fax macine on POTS) into tiff file (via Digium analogue card),

Hi *, Does anyone have a lead on a Nagios plugin that speaks IAX or a small app to do so? I'm trying to set up remote monitoring for my Asterisk server and only IAX2 traffic is allowed through the firewall. Simply using check_udp to port 4569 yields no usable answer and Asterisk complains about receiving a midget packet or something like that :) jens

I'm relatively new to Wine. I've been hearing about it for a while now. I've look a various comments about Wine on the net and I seems like a lot of people have got it to work for them. I've even used at work to run Inno to create a simple windows installer, which work well, although the User Interface was ugly (probably some missing fonts and things). I have a laptop at home

Dear R-helpers, I have dataset (data.frame) like below, x1 x2 x3 x4 x5 x6 x7 x8 x9 ... x1200 0 0 0 1 1 0 0 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 1 0 0 1 1 1 1 0 1 1 0 0 1 1 ... How can I change automatically 0=no and 1=yes. Thank you very much in advance. Kindly regards, Muhammad

Good Day list, I have googled and wiki'd myself to no avail. Here is my setup. Asterisk Box Digium T1 card connected to an adtran Total Access 624. I need to pass ANI and DNIS information from asterisk to the analog devices hanging off the adtran. The digits are announced to the fxs devices between ring 1 and ring 2 (If I pick up the anlog phone after ring 1, I can hear them so I

Sam, Danny, J., all I am working with the radeon and radeonhd drivers seeing if I can get them to work with compiz 0.8.2.1 on my radeon x1200 laptop. My xorg .conf is: Section "Device" BoardName "RV350 NP" # Driver "radeon" Driver "radeonhd" Identifier "Device[0]" VendorName "ATI" EndSection I have tried

Hi all! I'm trying to get the cadprogram Vectorworks 2010 (VW) run with Wine. So far I have succeed in getting the program installed and to start up with a plain Wine installation in PClinuxOS 2010. To get the toolboxes and everything look normal I had to install GDI+ (gdiplus) via Winetricks. However the drawing area is still messed up after this even if the toolboxes look fine. On one

Can anybody tell me how I can set-up multiple access points with overlapping coverage, so that a moving WiFi phone user can continuesly use the phone. bye Ronald Wiplinger

Hi everyone, I'm trying to buy a small form-factor PC system for use with Asterisk and Hylafax in conjunction with a Eicon DIVA Server single-port ISDN card (needs full-size 5V PCI 2.2 slot, but PCI-X compatible). Use is very light - at most a single call at any one time. If the Mac Mini had a PCI slot I'd try to use that one, but oh well ;) Would anyone have some brand names or

Hello, My question is regarding the interpretation of --stats output and whether I have a performance issue or not. Can the client/server architecture (rsync client on one machine, rsync server on another machine) be far slowlier than a local rsync session ? This is the ouput of an rsync session: date rsync -v --recursive --links --perms --times --group --owner --xattrs --acls --delete

Listmates, This is no biggie, 8.6 is working well so far. However, I do notice 1-2 lines of pixelization at the top of the screen on keyboard rotate. I know this hasn't been there since the 0.5.6-0.6 days when compiz was first released for opensuse years ago. It wasn't there up through 8.2. The gpu is the radeon X1200 using the fglrx-legacy driver. Looking at the screenshot it actually

I've been working my way through the softphones listed on voip-info over the last few weeks and I've not really found anything to fit the bill. Has anyone had more luck? The environment is a small call centre of 5 users. Operators often need to be able to transfer calls to other operators with different specialties, so the softphone needs to be easy to use and quick to transfer calls.

Hello, I just started using asterisk, and have a question. I have setup two asterisk servers, A and B. A has a Digium TDM400 11B card (1 FXO and 1 FSX modules) and is connected to the PSTN. B has same, but is NOT connected to PSTN. I want to configure B to call A via iaxtel, and connect to the PSTN using A's line. How can I configure iaxtel dial plan for B in extensions.conf? I want to be

Hi, I want to configure X on a NEC PC with an ATI graphic card. Usually, I do that by hand, e. g.: # init 3 # X -configure --> first draft # mv xorg.conf.new /etc/X11 Then I edit this with Vi, step by step. Usually, this works, but not for ATI cards. Here, the first draft only gives me a "vesa" driver... though xorg-x11-drv-ati is installed. But then, when I replace Driver