Displaying 20 results from an estimated 300 matches similar to: "Zaptel/Zapata config from T410p to Brooktrout T1"
2003 Mar 04
1
Brooktrout T1/E1 cards and Asterisk
I have wanted to setup an Asterisk system for several months but have
been unable to do so because I lacked the funds for a T1 card to connect
my channel bank to the server. Recently, I acquired several Brooktrout
T1/E1 interface (PRI-PCI48VC/PRI-PCI64V-C) cards for the PCI bus.
According to the Brooktrout web site
http://www.brooktrout.com/products/netaccess_pri_pci/specs.html
Linux
2003 Aug 19
1
Brooktrout PRI-ISA48 card... info..
I have the option to purchase an Brooktrout PRI-ISA48 dual-span T1 card, which, upon checking with brooktrout, is supported for linux 2.x, but before I do this, I want to check and see what the opinions of your, the list members, and Mark, of course, as far as asterisk being able to use this card.
ANY information would be helpful, as this offer will expire to me very soon.
Thank you. :)
2005 Aug 10
1
Addendum to my post re: BrookTrout TR1034 T.38
Don't want the opening line of my post to be misconstrued.
"Anyone familiar with the BrookTrout TR1034 Fax Board, supports T.38 and
PSTN fax in an Asterisk environment?"
That's a question, not a statement. Curious if anyone has played with one
of these as an extension of an Asterisk server for T.38 faxing, did not mean
to imply it could, should or would play well with
2004 Dec 23
1
Qestion about TDM over enthernet
who can tell me how to do TDM over enthernet ?
pc a connect pc b only use TDM card?
thank you
John.
-----????-----
???: asterisk-users-bounces@lists.digium.com
[mailto:asterisk-users-bounces@lists.digium.com]??
asterisk-users-request@lists.digium.com
????: 2004?12?23? 11:47
???: asterisk-users@lists.digium.com
??: Asterisk-Users Digest, Vol 5, Issue 336
Send Asterisk-Users mailing list
2004 Jan 30
0
Re: DISA and authcodes (was: t410p)
[moved from -dev, as the thread is better suited for -users]
At 5:10 PM -0600 1/30/04, James Sharp wrote:
> > I've pretty much got the routing covered at this point, I'm just not sure
>> how to get the Asterisk system to answer and give me dialtone immediately.
>> Any ideas or recommendations would be greatly appreciated.
>
>app_disa will give answer and give
2010 Mar 18
0
Software for my laptop to send Fax via H.323 ?
I'm trying to test a Diaglogic BrookTrout SR140 card. It uses H.323.
Trying to find a way I could use my laptop to send a fax over H323 to the BrookTrout card for testing. Any thoughts? Normally I'd setup a FXS interface on a Cisco router and setup a h323 dial peer to the BrookTrout, but I didn't the router with me!
-----------------------------------------
Disclaimer:
This
2003 Nov 20
1
Linux Voice Mail Application??
Does anyone on this list know of any Linux based apps that will work with
Dialogic or Brooktrout that provides voice-mail/Autoattendant only?? It
seems that Panasonic, Avaya, and Mitel all use Unix/linux based OS on their
firmware for their proprietary voice mails.
My wish list would be;
A software that provides all of the drivers for a dialogic or brooktrout
board
Voice Mail
Messages in WAV
2004 May 03
3
RFD: With echo and other distortion, can ulaw/alaw line quality ever be good enough for faxing?
Folks,
I've been following recent discussions regarding echo and echo training with
much interest, since it's a problem we've never been able to eliminate here.
We're facing two challenges presently, and they may be related (or not):
a) Cisco 7960s in the office here echo back to our staff, but the customer
hears decent sound.
b) We've yet to be able to pass faxes through
2004 Jun 25
0
ATA186 (sip) in * dynamic mode
I've got my ATA's setup with DHCP, host=3Ddynamic, and turned the
registration on in the ATA
All is well as long as my sip.conf is configured using the phone number like
so...
[1231231234]
type=friend
host=dynamic
context=main
canreinvite=no
username=1231231234
secret=worknow
disallow=all
allow=ulaw
allow=alaw
It appears to me that the Cisco ATA (v3.1) will register the device using
the
2004 Apr 07
2
Siemens EWSD 13
Hi all,
Has anyone got any experience with hooking Asterisk up with a
Siemens EWSD 13 switch over a E1/PRI ?
We're located in Belgium (Europe) and one of our telecom partners
uses this switch.
We connected one of our TE410P ports with their switch, but the status
light on the TE410P card keeps blinking red.
On their side they are getting a DSA (distance service alarm) error, so
this
2003 Oct 17
4
Using channel banks
Hello Everyone,
What kind of hardware setup would I need to do if I want a T1 connection to PSTN
and have 48 users in office with analog phones. Will something work if I have a
T410P card in asterisk and have one T1 going to PSTN and other two to a channel
bank. I would then connect the 48 phones (FXS) to the channel bank! Thanks.
Deepak
2002 Oct 29
1
samba compiling error
Hello,
I have error on compiling time
I tried on HP-UX 11.00 system with gcc version 3.1 to compile samba source
Samba latest version source was dowloaded from www.us1.samba.org/samba/ftp
I attached log file with this error
thank you.
begin 600 samba_make.log.doc
M(R!M86ME#0HO=7-R+VQO8V%L+W-A;6)A+V)I;B(@+410241$25(](B]U<W(O
M;&]C86PO<V%M8F$O=F%R+VQO8VMS(B
2008 Mar 06
0
Asterisk 1.4 w/ realtime static zapata
i've been using *1.2 w/ realtime static zapata in mysql table
fine. but after i upgraded to 1.4. it seems like the zapata
table doesn't load correctly. i have to go in the console
and use the "zap restart" to get the zap channels register.
is this sounds like a bug or something i'm missing when
upgrading to 1.4?
--
Edwin Lam <edwin.lam at officegeneral.com>
Systems
2005 Sep 02
0
Zapata help needed howto configure nationalprefix for a single card
is where anyone who can tell me how it's possible to set nationalprefix &
internationalprefix for a single isdn-card and not for all installed cards
?
2003 Apr 03
1
PPP by default in zapata
Just wondering if there is a reason PPP support is compiled into zapata by
*default*:
# Uncomment for Generic PPP support (i.e. ZapRAS)
#
KFLAGS+=-DCONFIG_ZAPATA_PPP
Especially since the comments imply that it should be commented out by
default...
The main reason I ask is because I usually try to re-compile the kernel to
only include the bits that I need, and so I don't include PPP...
2003 Apr 18
1
/proc info on X100P's, zapata.conf
I just installed two new X100P's today in my RH7.3 box and was poking around
/proc
What does the RED refer to on board 2?
/proc/zaptel/1
Span 1: WCFXO/0 "Wildcard X101P Board 1"
1 WCFXO/0/0
/proc/zaptel/2
Span 2: WCFXO/1 "Wildcard X101P Board 2" RED
2 WCFXO/1/0
Any clues on how to setup channels on the two interfaces?? I am up to here in
2003 Apr 19
1
zapata busy detect
hi!
when i have busy signal on analog line (zap card) it doesn't detect
that line is busy ?
is it possible to change detected sequence (frequency) of busy tones on
line (zapata.conf ??)
tnx,
Thomas
my zapata.conf
[channels]
language=en
context=lin1
signalling=fxs_ks
channel => 1
group=1
echocancel=yes
echocancelwhenbridged=yes
rxgain=3.0
txgain=3.0
busydetect=yes
2003 Jul 30
0
rxgain and txgain in zapata.conf
Hi,
Do you have some experience with the "best" values for those parameters in
youyr particular case?
I mean the best raport between sound level in both direction and echo
cancellation.
For me, the best result I can get is with:
rxgain=10
txgain=15
... the sound level is good, but the echo is a little bit to strong for my
taste.
Something interesting is that if I put a txgain value
2003 Sep 10
2
NO TONE ON ZAPATA FXS CHANNEL
Hi
I've problem, i cant get tone on a FXS ZAP channel my configuration are:
-- zaptel.conf --
fxoks=1
--zapata.conf --
[channels]
immediate=yes
context=bell
signalling=fxo_ks
channel=1
--extensions.conf --
[home]
exten => 500,1,Dial(IAX2/guest@misery.digium.com/s@default)
[bell]
exten => s,1,SetCallerId(${CALLERID})
exten => s,2,Dial(${PHONE},16,tr)
ANY IDEA?
2004 Apr 08
2
Zapata required?
Hello-
As part of the asterisk build/installation instructions it mentions that the
zaptel drivers should be built and configured first. My question is whether
they are required at all, in the case of a system with no hardware cards at
all (as is the situation in my case).
With them loaded I continually get the following message on my console
(server not asterisk):
Zapata Telephony Interface