similar to: Cisco 7960 (SIP) hold problems

Slightly off topic, but maybe some can suggest something off list... Trying to upgrade a 7960 that was running skinny. I've got sip v3.2.0 installed and running, and am able to place calls via *, etc. However, when upgrading to v4.4.0 I can never get to the point of being able to place a call (eg, no dialtone, etc). I can ping the phone, look at the Network Config, etc, but I can't

Hello: I am testing Asterisk with oh323. My question is: can Asterisk route some calls thru a second h323 gateway (a h323 <-> PSTN gw)? - Asterisk ip: 192.168.1.10 - h323<->PSTN gw: 192.168.1.20 I've tried: exten => _9XXXXXXXX,1,Dial(OH323/192.1.1.20) or exten => _9XXXXXXXX,1,Dial(OH323/BYEXTENSION@192.1.1.20) but it does not work at all. If my h323 client

I have multiple voiceage g729 licenses installed on a RH9 box, and have a remote C7960 configured to use it (low bandwidth). In calls like: Remote C7960 -> g729 -> asterisk -> g711 -> C7960 the audio is oftentimes rather choppy. Changing the remote 7960 to use g711 seems to eliminate/reduce the choppyness. Any ideas on what might be behind this?

Hello, Does asterisk do transcoding when the call goes through the system, codecs are the same but signaling protocol is changed. example: SIP with GSM ---> IAX with GSM What quality destruction happen when I use transcoding? I know this is not a concrete/precise question, but I would like to know how is it in general. What CPU performance is needed for transcoding 30 channels e.g. from

ala cisco 7960 -----Original Message----- From: Matt Schulte Sent: Thursday, December 16, 2004 10:34 AM To: 'Paul A Brown' Subject: RE: [Asterisk-Users] Cisco 7960 (SIP) hold problems Sure thing, the biggest problem I had was getting the SIP filenames working correctly for updating the firmware (blah, I love Cisco but these phones are a joke for support). This works for me! Good luck.

Hi Rich, I had to change all my nat=yes to nat=route in the sip.conf. nat=yes seems to be ignored in today's CVS. Walter > > Message: 5 > Date: Fri, 27 Aug 2004 08:45:19 -0600 > From: Rich Adamson <radamson@routers.com> > Subject: Re: [Asterisk-Users] sip change? > To: Asterisk Users Mailing List - Non-Commercial Discussion >

Hi, I have read a lot about the thread of faxing support in Asterisk as well as spanDSP. However, either I don't fully understand other people's applications or may be what I'm trying to do is different from what others are trying to do. I have a very simple setup. I have an asterisk server with a TE110P connected to the PSTN via T1 PRI (Asterisk A). I have another asterisk

Isn't it about time to lock down added functionality to v1.1 and fix the remaining bugs? There has been a significant amount of traffic on the cvs list, the irc and other channels with folks spending time adding new functionality to Head. Think its time to lock it down, fix the bugs that have been introduced, and get to "something" that the _majority_ can agree to call v1.1 Stable

We are in the process of an Asterisk call center deployment using IAX2 G711 ulaw softphones. Outbound sound quality is terrible. This week we rebuilt the entire LAN with Cisco 2950-EI switches and have employed QoS on the switches and router. Still sounds terrible. What we are now finding is that the network card in the PC may be the key to the problem. A Dell Optiplex P4 2.4GHz 512MB

Hi All, I am running into a problem setting the ringtones via _ALERT_INFO on the Cisco 7960 phone. I am using * 1.2.1 and have tried setting the variable to several values. I have also tried setting the phone's software to both 7.5 and 8.2 thinking that it might be a version issue, but with no success. I have examined the packets and do see the ALERT_INFO header being sent, but the

Using the following defnitions with a C7960: exten => 3001,1,Dial(SIP/3001,15,r) exten => 3001,2,Voicemail2(u3001) exten => 3001,102,Voicemail2(b3001) exten => 3001,103,Hangup If someone is on this phone (real conversation) and another call comes in, the second call goes through the 15 second timeout and is dropped into the 2-priority as "unavailable" (not the 102 busy as

Anyone had any good/bad/otherwise experience with the Mediatrix 1204 Sip FXO 4-port gateway? The archives tend to suggest the box is not very straight forward, and possibly lacks some basic pstn interaction features. Thinking about trying one in place of a pair of x100p's (functioning fine now). CallerId, etc, supported on this gateway? Rich

I'm about to download Festival source, apply the astrisk diff's, and initiate basic testing. Thoughts are to download v1.4.3 (latest per the fesitval website. If anyone has an existing how-to, install notes, tips, or any suggestions I'd greatly appreciate it. Direct email is fine if you'd rather not post them. Thanks, Rich radamson@routers.com

Just turned up a new PRI with DID's in the US. I'm receiving 5 digits of the DID numbers as I requested. Assuming I have 100 DID numbers but only define 50 of those in extensions.conf, is there an easy way to send the incoming calls for the 20 undefined numbers to a common resource (ivr, operator, or canned message) without having to define each one?

Anyone interfaced * to the Nortel option 61c pbx via T1's, pri, etc? Need to begin planning the implementation, purchase cards, etc. Any recommended approaches, configuration problems, etc? Off-list is fine if you'd like. Rich radamson @ routers . com

Does anyone know how to get a Cisco 7940 w/FW ver 2.0.3 to v3x and above. Can't get it to upgrade on its own via TFTP. Phones w SCCP image will upgrade fine but I can't get these 2.0.3s to start the firmware upgrade. Thanks. Regards, Juan Staalenburg Teksavers, Inc. (512) 255-8395 x1002 AIM: juanteksavers

Hi, I know that SIP is using port 5060 for session initiation, but which port does it use for audio ? is it dynamically assigned ? Thanks, Adrien -- Adrien Laurent - CIO www.modulis.ca 514-284-2020 ext 202 adrien@modulis.ca

Why is it that the wiki indirectly recommends SER (or another proxy) out in front of Asterisk. If Asterisk can use radius, and provide the rest of AAA they why ? Incidentall\y, I'm not familiar with network configuration really, although I do understand most of the basics. --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version:

Does anyone have a working way of having a Cisco 7960 reload its config remotely. I have tried some of the scripts that I have found on the web, but to no avail. Thanks for the help. B. J. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040116/aa4eda3c/attachment.htm

For those that might be using Cisco 7940/7960 sip phones and placing calls across an iax2 link, we think the voice quality problem has been identified and corrected. The dev cvs should be updated as of about 3:30pm CDT today (April 14). History: Calls originating from a Cisco 79x0 sip phone and sent via iax2 link to some distant * machine resulted in very poor quality audio, and in some cases,