similar to: PRI Errors again... sigh.

FYI: I hope that this is not a "me" error and that Digium can squash this bug (or new hardware fixes it). Either way, when this is over, perhaps I can provide some troubleshooting documentation for these errors. ---------- Forwarded message ---------- Date: Mon, 3 Jan 2005 09:36:51 -0500 (EST) From: Andrew McRory <amcrory@linuxsys.com> To: support@digium.com Subject: PRI Errors

Available in the usual place. ftp://ftp.linuxsys.com/pub/releases/CentOS-4.0 This release includes minor spec changes, spandsp 0.0.2pre23, a new Sangoma wanpipe RPM for use with the LSE kernel rpm and an AMP installation document. Best Regards, -- Andrew McRory - President/CTO Linux Systems Engineers, Inc. - http://www.linuxsys.com Located in beautiful Tallahassee, Florida Office

On Thu, 5 Aug 2004 asterisk-users-request@lists.digium.com wrote: > Date: Thu, 5 Aug 2004 14:56:06 -0400 (EDT) > From: Andrew McRory <amcrory@linuxsys.com> > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] PRI Errors... Ouch > Reply-To: asterisk-users@lists.digium.com > > > Today is the first time I've had any show stopping errors with asterisk

Greetings list, It's been a while since I've been able to focus on asterisk packaging but this weekend I took some time to audit and recompile packages for CentOS 4.2. You can find them here. ftp://ftp.linuxsys.com/ftp/pub/releases/CentOS-4.0 You have your choice of 1.2.1 or 1.0.10 releases. If you need zaptel modules then install this kernel as well:

Hello, I've uploaded current builds to ftp://ftp.linuxsys.com/pub/releases/FC2/asterisk-CVS ftp://ftp.linuxsys.com/pub/releases/FC2/asterisk-1.0 Regards, -- Andrew McRory - President and Chief Techincal Officer Linux Systems Engineers, Inc. - http://www.linuxsys.com Located in beautiful Tallahassee, Florida Office 850-224-5737 Office 850-575-7213 Mobile 850-294-7567

UPDATE. The circuit has run clean since the 7th. It seems the telco found a problem after all but they can't tell me what they did... cause they think it was fixed as part of another case. Grrr. Well, I never doubted the T400P too much but I went ahead and bought a different card just in case. Haven't had to use it so far. One of the biggest reasons I did not think the Wildcard was at

Hi folks, Anyone want to check out the subject packages will find them here: ftp://www.linuxsys.com/pub/testing/asterisk The asterisk RPMS now include builds of asterisk, addons, astcc, btp, gastman, iaxproxy, libpri and zaptel from 10.04.04 CVS. zaptel is compiled and working with kernel-2.4.22-0.FC1.LSE.p3.i686.rpm available with ALSA modules and supporting packages here:

I created a tarball for redhat 7.3 with kernel 2.4.28, asterisk v1.0.3-CVS-01.04.05 and alsa-1.0.6a... see the README / download it here: ftp://ftp.linuxsys.com/pub/packages/rh73/asterisk/ -- Andrew McRory - President/CTO Linux Systems Engineers, Inc. - http://www.linuxsys.com Located in beautiful Tallahassee, Florida Office 850-224-5737 Office 850-575-7213 Mobile 850-294-7567

System is built on a SuperMicro motherboard with Serverworks chipset, IRQ is not shared. Have a dialplan that worked for 8 months without errors, tried reverting to older release then upgraded to 1.0.3 stable release, currently running on fedora core 1 kernel 2.4.22-nptl.2199 (have tried plain jayne), telco says "it's not us", HDLC abort seems to occur when when a Zap channel hangs

safe_asterisk used to work fine but with v1.0.3 I am getting all kinds of permission errors, intermittant failures, etc. Even with file permissions relaxed and ownership set to asterisk it craps out. Seems to work fine when run as root. Comments??? -- Andrew McRory - President/CTO Linux Systems Engineers, Inc. - http://www.linuxsys.com Located in beautiful Tallahassee, Florida Office

Today is the first time I've had any show stopping errors with asterisk since I started using it over 8 months ago... While I wait on the telco to check the circuit I thought I would post this here. Not sure yet but I thinks my 4-port PRI card is gone!!! I made a call and right when the person answered - BOOM. This is only a little better than it not working at all.

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Well I am about to reserve a small padded room so I can bounce off the walls without inflicting tooo much damage... Nothing is making sense at this point. I tried several releases last night before settling on the latest CVS (seemed to work the best). Asterisk was running GREAT for the first few hours. Now since around 10AM EST SIP can't register and incoming calls are rejected with "all

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

Hello All, I have got my TE110P working at the hardware level, turned out to be a dodgy cable causing the Yellow errors in zttool. However, now I am getting yellow errors in asterisk, but zttool shows nothing out of the ordinary. here is my current config, and some asterisk console errors, any suggestions most welcome. zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route