similar to: Busy message on ISDN cards?

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi, I successfully installed 2 avm card in my asterisk box but I'm unable to make call. My capi.conf is: msn=0721111,07211115 incomingmsn=* controller=1,2 softdtmf=1 context=default echocancel=yes callgroup=1 devices=2,2 my capi info : Contr1: 2 B channels total, 2 B channels free. Contr2: 2 B channels total, 2 B channels free. my extensions.conf : exten =>

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

Hi After modprobe hisax type=35 (Billion HFC PCI) on a Xorcom Rapid ISO I get: HISAX Dec 12 16:25:35 localhost kernel: HiSax: Linux Driver for passive ISDN cards Dec 12 16:25:35 localhost kernel: HiSax: Version 3.5 (module) Dec 12 16:25:35 localhost kernel: HiSax: Layer1 Revision 1.1.4.1 Dec 12 16:25:35 localhost kernel: HiSax: Layer2 Revision 1.1.4.1 Dec 12 16:25:35 localhost kernel: HiSax:

----- Original Message ----- From: Karl Heyes <karl@pts.tele2.co.uk> To: <icecast@xiph.org> Sent: Friday, January 31, 2003 5:29 PM Subject: Re: [icecast] Re: Compiling ices <p>> On Fri, 2003-01-31 at 06:39, Marc Remijn wrote: > ... > > > Kernel output: > > > > invalid operand: 0000 > > CPU: 0 > > EIP: 0010:[<d08e25b1>]

I tried that but it still doesn't work... I think I don't have the correct approach. Have I to install any ISDN drivers (=modules ?) BEFORE dealing with CAPI ? If yes, why shouldn't I use the hisax drivers (which are kernel ones) instead of fcpci drivers (which doesn't seems to work, by the way...) And finally, how is it possible to link the two modules together? As you can see,

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

Hi all, i have asterisk 1.0.9 with an Eicon Diva 4bri and chan_capi-cm-0.6. I have 2 NTBAs (one with did and one without). When using the one without did, i am able to place outgoing and incoming calls. When i use the NTBAs with did i have a layer 2 error. Anyone an idea? -- Executing Dial("SIP/2004-9634", "CAPI/g1/43XXXXXX") in new stack > data = g1/43XXXXXX

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hi, First, here is my config: Kernel version 2.4.25 on a Fedora distro, Asterisk and a Fritz! Isdn PCI Card (v2). I try to make the CAPI drivers deal with Asterisk but I can't try to figure out to get of this issue. As I see, Fritz modules are integrated with the kernel, so I directly loaded the 'hisax_fcpcipnp' module from it. I install also Capi modules by downloading archives of the

I have * with i4l installed and working - on a dumb eicon card. It seems in order to get DTMF out of the BRI (for business banking - etc) - I should change from i4l drivers to capi drivers. wiki help seems to be for the Fritz card only...??? I have ticked the suggested boxes in 'menuconfig', explored the capi4linux websites - etc... but am missing some magic. I've "modprobe

I've put my fire proof suit on ready to ask a question ;o) Redhat 9 Kernel 2.4.20-8 AVM Fritz PCI Problem 1... i have followed instructions from:- http://www.voip-info.org/wiki-Asterisk+AVM+Fritz+CAPI+Driver+Install http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI (Plus many many other sites found via google over the last 16 hours) after modifying the makefile & defs.h,

Hi all, I'm experimenting with Asterisk on linux using an Eicon Diva 2.01 S/T PCI card. I'd set up the card using the hisax driver and isdn4linux (titled as "Old ISDN4Linux (obsolete)" in the 2.6.12 kernel. I can make SIP calls and outgoing phone calls as well, but gathered a few problems on my way: 1. Plain SIP calls using softphones on windows clients work fine not counting

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,