similar to: Apply Patch for Broadvoice.

Hi all, a noob here, I am trying to get outbound calls through asterisk working with Broadvoice. I have consulted the following two online tutorials: http://www.broadvoice.com/support_install_asterisk.html http://www.voip-info.org/wiki/view/Asterisk+settings+Broadvoice in an effort to make outbound calls. My current settings are as follows: sip.conf register =>

Whats the deal with this Broadvoice patch?

Hi folks. Thanks for having patience with a newbie... I am going through the setup exercise at http://chayden.net/Asterisk/SeUpAsteriskAtHome.htm I am trying to do it all on BroadVoice since this is just experimental, and the 100 minutes of outgoing from them should be enough for now. So I set up BroadVoice for both inbound and outbound, using a combination of the instructions referenced

Is the broadvoice patch part of asterisk 1.0.4? The changelog does not mention it. Thanks, Jerry

Hello, I am sorry that I post questios regarding Broadvoice here, but unfortunalelly their support is very very bad. The simply do not answer to any emails or telephones. Last week something happened to their system. I was not able to receive incommming calls etc. Now it is back, but the voice quality is terribe and the DTMF is not working.(Is the inbound mode the correct one?) Does anybody knows

Hello Asterisk People, I am having trouble connecting asterisk to a huawei SoftX3000 Switch, i can succesfully connect other softphones like Zoiper, but when it comes to Asterisk SIP Client, the system doesn't authenticate, i have the following configuration: peer: 10.220.0.2 username: 4857768 password: 4857768 the configuration is as follows: in the general section: register =>

Okay, I installed http://www.xorcom.com/rapid/ Xorcom'ms Rapid distro. I had broadvoice working with the following settings described on the list and as well as broadvoices website. (http://www.broadvoice.com/support_install_asterisk.html) I'm trying to run another Distro (CentOS) and everything is installed and working fine with MySQL. However, the "same" configs give me the

Hello, I am just curious how many people are hooked up with BroadVoice and have recently been experiencing a lot of dificulty. Joel

Is anyone else experiencing 404 errors on outbound dial with Broadvoice? I've followed the instructions posted by Broadvoice to configure sip.conf, and inbound calling works fine. Every time I try to dial out, I get a 404 "Not Found" error. Here are the relevant sections from my configs. sip.conf: context=broadvoice-in register =>

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

Hello all, When I call the Broadvoice number all is good. When I try to call out through DISA on my broadvoice line i get the following: Executing Dial("SIP/147.135.0.129-0815bc60", "SIP/16037862111@proxy.bos.broadvoice.com|30") in new stack -- Called 16037862111@proxy.bos.broadvoice.com -- Got SIP response 480 "Temporarily Not Available" back from

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

Hello All, I have 4 Broadvoice lines. If I call any of the lines it shows that is coming from the first line. exaple register=XXXXXXXXX1@sip.broadvoice.com:passwd:XXXXXXXXX1@sip.broadvoice.com register=XXXXXXXXX2@sip.broadvoice.com:passwd:XXXXXXXXX2@sip.broadvoice.com register=XXXXXXXXX3@sip.broadvoice.com:passwd:XXXXXXXXX3@sip.broadvoice.com

So it was all working well and then suddenly I'm unable to get incoming calls from BV. Outgoing is fine. I'm using AAH. I have the following settings; register=9738281625@sip.broadvoice.com:PASSWORD-GOES-HERE:9738281625@sip.broadvoice.com/2208 [broadvoice] username=9738281625 user=phone type=peer secret=PASSWORD-GOES-HERE qualify=1000 port=5060 nat=yes insecure=very

I finally got my incoming and outgoing to work on Broadvoice with a configuration file that is no where close to the one given by them. Here it Is (sip.conf). For others who have a working config could u please share so that I could compare. Thank You [broadvoice] type=friend username=[number] fromuser=[number] secret=[password] host=sip.broadvoice.com fromdomain=sip.broadvoice.com

Connecting to proxy.dca.broadvoice.com Calls all of a sudden cannot be completed. Cannot ping proxy.dca.broadvoice.com Changed to proxy.chi.broadvoice.com pingable, but now get the following: Got SIP response 500 "Internal Server Error" back from 147.135.12.128internal error Called Tech Support... get dead air then carrier busy signal. Anyone else having

All, I have been fighting with my dialplan for hours now, and google searches talk lots but offer nothing in terms of explication for this. I have my SIP peer set up and working with Broadvoice: [sip.broadvoice.com] type=peer user=phone host=sip.broadvoice.com fromdomain=sip.broadvoice.com fromuser=5555551234 secret=password defaultuser=5555551234 insecure=port,invite context=broadvoice

Egad, not again with Broadvoice! Anyhow, I recently installed AAH and configured my TDM11B and got that and some SIP phones working. I still have some issues to work out, etc, but my current problem is Broadvoice. I have checked out all of the online resources, including the recent list exchange about the recent changes made by Broadvoice. However, the one thing I have found to be consitent in

Hi all, I've been trying to use BroadVoice as a SIP service provider. They don't officially support * but are helpful when it comes to answering questions for setup parameters. They claim they have no firewalls or access lists that need to be set up so I can get access to their servers. However, something's still not quite right when I use the parameters. It looks like our Asterisk

I've setup Asterisk to work with Broadvoice for both incoming and outgoing calls. I can make outgoing calls, but when I try to receive an incoming call I see the following message on the console: [date] NOTICE[8661]: chan_sip.c:13178 handle_request_invite: Unable to create/find SIP channel for this INVITE It's registered with Broadvoice: Name/username Host Dyn