similar to: Asterisk from CVS

I am looking for a supplier of Digium hardware in Canada. Any suggetions? Thanks, Adi

Hi, What is out there in terms of SIP enabled handsfree speakerphones? Looking for something that works well and also fits a low budget. I am used to using a Cisco 7940. It is a great phone but a bit expensive. Thought about the Polycom SoundPoint 300 until I realized that it does not include speakerphone functionality. Thanks, Adi

My PSTN line doesn't allways hang up properly after it goes to voicemail. The problem occurs when a caller hangs up during the initial greeting. Even though the hangup accured, voicemail continues to record, usually a fast busy and/or a teleco generated "please hangup now" message. After the voicemail.conf 'maxmessage=180' expires the line simply stays offhook. The hardware

Hi, I've been looking at the various SIP VoIP service providers and their plans. I understand that Asterisk can be configured as a SIP client to access, for example, a BroadVoice account to access the PSTN and discount LD. I see that a lot of the features provided by SIP VoIP service providers are really not needed since Asterisk will provide them locally. I have no plans on dropping my

Hi, Where can I find information on H.323 for Asterisk and/or integration with Cisco CallManager in particular? <http://www.voip-info.org/tiki-index.php?page=Asterisk+Cisco+CallManager+Integration> I have oh323 working on Asterisk. Since the CallManger I am working with is running 3.3.3 I cannot use SIP... Thanks, Adi

Hi, How well to the Cisco 7905G or Cisco 7912G phone work with Asterisk? Cisco claims both phones do SIP. I was strongly considering Polycom phones. However, it appears to be quite difficult to obtain support or firmware for Polycom phones. On the other hand, I find Cisco is very well supported. Thanks, Adi

Hi List, I've got * randomly hanging up on inbound or outbound calls on zap channels. I use a Digitnetworks X100P clone card. Any idea of what might be happening? Cheers, Jean-Michel.

OK. I just downloaded asterisk-1.0.3.tar.gz and did a 'cvs co -r v1-0 asterisk' into 2 seperate directories. I then did 'diff -ur asterisk-cvs/ asterisk-1.0.3/' and there were source code line differences between the two. Some code that was in asterisk-cvs wasn't in asterisk-1.0.3 and vice versa. Which of those is "the most recent"? If someone wants to use cvs to

We are in the process of testing * for company wide deployment. We are using Polycom 300 phones, the only problem that I am running into is when I call an 800 number that has an IVR I get disconnected after about 60 seconds. Here are the logs from asterisk. I am not sure if this is a problem with asterisk timing out or if it is the phone. To me this looks like asterisk is timing out.

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

On how to even search for this "feature" as I have no idea on what it can be. I've got a meridian linked to * (by EuroISDN) which is linked to a ISDN30. I can make calls from the meridian, and receive calls into the meridian. Great stuff. However, if someone dials an invalid number, then instead of hearing a "three tone", the line just drops and goes dead. The console

How can i control the codec for the calls. For example I have 3 SIP phones registered to asterisk The firs two are in the local area network (behind nat)- I want to use g711 between them and to connect directly (canreinvite=yes) and the third is in internet - want all calls to it and from it to use g729 and media to go through asterisk. So if Phone 1 calls Phone 2 the codec to be g711, but when

HI ALL: I am newbie to IAX, my iax.conf is as follows: [general] port=5036 ..... but I donot why it doesnot listen on UDP PROT 5035, instead it listens on 4569 Asterisk CLI debug says: [chan_iax2.so] => (Inter Asterisk eXchange (Ver 2)) == Manager registered action IAXpeers == Parsing '/etc/asterisk/iax.conf': Found Nov 30 11:52:12 WARNING[1076220544]:

When I make a call from a SIP phone to a speaking extension on *, such as one that speaks digits or similar, when I monitor * in very verbose mode I can see it running through the routine associated with the extension, but I am getting no RTP data stream back to the phone. Does the machine housing * need a sound card? Does it need OSS or ALSA modules installed? What actually generates the RTP

I've configured an analog/single line off my mitel sx-2000 to a x100p card in my *, however when the remote caller drops the line I get a dialtone back from my pbx and the x100p doesn't detect the end of the call. Any way I can tell * to drop? I've tried call progress but it doesn't seem to work...

Hello, I've 3 * boxes connected with IAX2. Everything was working correctly and since few days, after upgrading them to Asterisk 1.02, i started seeing IAX2 notify messages excahnges on port number 1024 and 1040 in addition to the specific 4569 iax2 port, is that normal ? All call between * boxes are rejected with "NO SUCH EXTENSION or CONTEXT" message, I've checked my

Hi, I compiled * and chan_alsa.so is loaded. But I can't hear any busy signal messages when calls cannot connect. Do I need to record my own message, or does * use some default ones? May I ask where can I find them? Regards, Norman Zhang

Hey gang, Getting ready to run some test bills for customers. Most SIP phones have both an extension and a DID. If a person calls a DID asterisk redirects the call to the right extension: exten => 8005551212,1,Goto(companyA-internal,3022,1) The problem is, that if someone calls 8005551212, the CDR shows the DST number as 3022. Is there a way around this? I understand that 3022 is the

Hello I try to set up voicemails for extension. When VoicemailMain gets called, it prompts for mailbox and password. It seems not able to read from the phone. So the authentication always fails. I desparately need help to understand what is wrong. Here is a part of my extensions.conf: exten => _8500, 1, Wait(2) exten => _8500, 2, VoicemailMain(${CALLERIDNUM}) exten => _8500, 3, Hangup

HI; I have an Asterisk with 10 "SIP" ip-phones, our pbx features are now: Voicemail and Call Transfer. How can I serve both "Call Waiting / 3 way calling" for our SIP Phones.?/ Appreciate Any Help Mohammad -------------- next part -------------- An HTML attachment was scrubbed... URL: