similar to: Broadvoice and incoming DTMF

Hi, all. The asterisk setup is working fine, receiving calls via broadvoice "initially". ? When call comes in via broadvoice number, asterisk picks it up and routes correctly, as long as the call came in within ~2 min from the previous one. In other words, as long as a call comes in within ~2 min since the previous one, asterisk will answer the call. However, if the call comes in

I finally got my incoming and outgoing to work on Broadvoice with a configuration file that is no where close to the one given by them. Here it Is (sip.conf). For others who have a working config could u please share so that I could compare. Thank You [broadvoice] type=friend username=[number] fromuser=[number] secret=[password] host=sip.broadvoice.com fromdomain=sip.broadvoice.com

So it was all working well and then suddenly I'm unable to get incoming calls from BV. Outgoing is fine. I'm using AAH. I have the following settings; register=9738281625@sip.broadvoice.com:PASSWORD-GOES-HERE:9738281625@sip.broadvoice.com/2208 [broadvoice] username=9738281625 user=phone type=peer secret=PASSWORD-GOES-HERE qualify=1000 port=5060 nat=yes insecure=very

I have been going crazy with this also since Sat. Our server was working perfectly with BV but will now not place calls to BV. Incoming from BV works fine. I felt sad rebooting it today, it had been running for almost 200 days! Here is my error message from the console... Notice I am running today's CVS Connected to Asterisk CVS-03/08/05-14:32:39 currently running on com (pid = 1624)

HELP! Ok, so I have the following SIP.CONF: [general] context=default port=5060 bindaddr=10.1.1.200 externip = XX.XXX.XX.XX localnet=10.0.0.0/255.0.0.0 disallow=all allow=ulaw allow=g729 allow=g726 allow=alaw register => ##########@sip.broadvoice.com:XXXXXXXXX:##########@sip.broadvoice.com/1234 [sip.broadvoice.com] type=peer host=sip.broadvoice.com fromdomain=sip.broadvoice.com

Hi all, I've been trying to use BroadVoice as a SIP service provider. They don't officially support * but are helpful when it comes to answering questions for setup parameters. They claim they have no firewalls or access lists that need to be set up so I can get access to their servers. However, something's still not quite right when I use the parameters. It looks like our Asterisk

I understand there has been some issues sending DTMF tone through Broadvoice. Can some provide me with symptoms? --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.700 / Virus Database: 457 - Release Date: 6/6/2004

I have configured asterisk with the AMP php configuration utility. I am able to make outgoing calls through broadvoice but incoming calls are sent to BV's Voicemail and never actually enter the IVR. When I show sip debug info through the asterisk prompt it actually reads the incoming call from BV but then issues a busy signal sending the call to BV's voicemail. I also modified

Asterisk seems to register just fine with BroadVoice (asterisk -r, and then sip show registry shows sip.broadvoice.com is "Registered") ...but when I try to call my broadvoice number (from a cell phone), it rings one single time and then says "The party you are trying to reach is not available to take your call." This doesn't seem to be an Asterisk message but seems to be

Is anyone else experiencing 404 errors on outbound dial with Broadvoice? I've followed the instructions posted by Broadvoice to configure sip.conf, and inbound calling works fine. Every time I try to dial out, I get a 404 "Not Found" error. Here are the relevant sections from my configs. sip.conf: context=broadvoice-in register =>

I just signed up for the BroadVoice service a few hours ago, but for the life of me I can't get any incoming voice. The incoming connection is fine as it rings my extension from outside, but I can't hear anyone talking. Outgoing voice is working fine though. I've been looking through the archives, but I haven't found a solution to the problem yet. I even tried another router

Hi all, I just upgraded to Asterisk 1.4.18 a few days ago and I don't use Broadvoice TOO often, however I have a Vermont number with them and so my mother in law calls it to talk to my wife once in a while, so that's why it took me so long to notice it wasn't working. Anyway, when she calls she gets a busy signal (as I've tested when calling it from my cell). When I enable

Hello all, When I call the Broadvoice number all is good. When I try to call out through DISA on my broadvoice line i get the following: Executing Dial("SIP/147.135.0.129-0815bc60", "SIP/16037862111@proxy.bos.broadvoice.com|30") in new stack -- Called 16037862111@proxy.bos.broadvoice.com -- Got SIP response 480 "Temporarily Not Available" back from

Hello All, I'm just getting into *, and trying to use a Broadvoice account. It works inbound, but Outbound fails no matter what sip.conf parameters I try. From the recent posts here I think it could be: A bad CVS release - I will try to download and build from a new one Broadvoice not challenging and/or Asterisk not responding with an Authorization: in the INVITE header. I am

I did a quick google search of the lists site and couldn't find a definitive answer, so if it's there, I apologize for asking again. Starting about noon yesterday, I am no longer able to send/receive calls via Broadvoice. When calling in, I get a fast busy, and when calling out I get the following error: -- Executing Dial("SIP/112-572a",

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

I have tried everything to get BV working outbound. All worked fine until the BV change last week. I called BV and they changed me to sip gen with a new password. I stripped my Asterisk server to one phone on Zap/1 until I get this working. The same BV account works fine with a SPA-3000 so I don't suspect a firewall problem. Symptoms: Asterisk registers with BV Ok Incoming calls work

I configured this once now I forgot what I did. Two Broadvoice accounts. Incoming is simple - just use the phone numbers. Outgoing: Dial out on a specific line and/or set up the groups and select the other "line" if the first one is busy? -- James Taylor MetroTel 3505 Summerihll Road Suite 11 Texarkana, Texas 75503 903-793-1956

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

Hi, I can't make outgoing calls via Broadvoice. I have tried each and every configuration that was posted to list previously. I am able to receive incoming calls fine. I get the following in asterisk console: ===================================================== asterisk*CLI> show version Asterisk CVS-HEAD-03/10/05-22:51:28 built by vicky@asterisk on a i686 running Linux