similar to: TDM OnHook/OffHook

> -----Original Message----- > From: Jacqueline Lee [mailto:jlee@isdomaininc.com] > Sent: Friday, September 23, 2005 11:46 AM > To: asterisk-users@lists.digium.com > Subject: channel offhook state > > > We are using a digium card (TDM400) with asterisk for our access to the > PSTN. Initially when the server starts, all the zap channels on the card > are in the

>Asterisk and it works fine untill the following >situation: > >- one of the telco lines occasionally becomes mute after call is completed, would not provide dial tone, (not sure about ringing on that >line) - both via old and new PBX. >- zap show channel <n> would show that line as 'Offhook', though no telephone is off hook. > >If physical line would be

Hi, I'm having an interesting problem with my card. It seems to work fine, for the most part. When I first load the module and asterisk, it detects the line in the on-hook state. However, after the first phone call, zap show channel 1 lists it as being off-hook. During subsequent calls, the card is listed as being on-hook, and when it's not used -- off-hook. There are also some weird

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

I've been having trouble with making outbound calls to my TELCO from a TDM400 card (FXS KS signalling) after upgrading from 1.6-beta9 to 1.6.0. The problem is completely intermittent. When it fails, I get this message: [Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) At some point, it starts working, but I don't know what

Hello, In my quest to figure out the source of the random echo on our shiny new asterisk install, I have been using ztmonitor on the TDM400p channels for the good part of today. I have 2 TDM400p cards with 8 FXO modules and 6 pots lines connected to them (last 2 channels are unused but configured in zaptel). Even when the lines are onhook, the Tx values settle down to 0 but the Rx values still

OK... so I'm not sure what I'm looking at. I've had the good old echo problems on my Rev C FXO again this morning, so I thought I'd attempt some debugging, though I'm not sure what I'm looking at. This call has echo. Channel: 2 File Descriptor: 20 Span: 1I> Extension: Dialing: no Context: incoming Caller ID string: "External Call" <99999999> Destroy:

Hi, On Sun Jun 12 09:11:13 CDT 2005, Rich Adamson wrote: > > > exten => s,1,Wait(1) > > exten => s,2,GoTo(s,1) > > > > If I'm on the console when a call comes in, it loops through this bit of > > code a bunch of times. I'm guessing I could lengthen the "Wait(1)" time, > > but is there any other way to do this? > > Sure there is,

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Hi, I'm trying to make a dialup internet connection through my asterisk PBX. When I bipass the Asterisk box, I can get 51600bps. When I run through the asterisk box, I'm limited to about 21600bps. I have a TDM31B card. Any help on speeding these connections up would be good - I was on the understanding that if you bridged the channels, then the call should essentially flow straight

Does anybody know if there are any external telephone-keypads for sale anywhere? (containing the keys 0-9, *, # and onhook/offhook would do) I am looking for a keypad to control a softphone and would prefer the controls to be in the physical world instead of as a window. Sincerely, Markus Hakansson

Hi, the new Grandstream release for the ATAs allows the setting of the FXS impedence, the Onhook Voltage and the Polarity Reversal. Anyone know how these should be set in Germany? -- Best regards Peer Oliver Schmidt

Hello, Caller -> PRI -> SIP -> application. If application goes offhook right away, dtmf/audio works fine in both directions. If application, before going offhook (sending OK) plays a message and wants dtmf/voice from the caller, then caller can hear this message but his dtmf/voice don't reach application. Any way to configure it? Thank you. Alex Zarubin -------------- next

Hi, I have a analog phone connect to a WCTDM card. It used to work fine. Now recently, after several conf change and power restart, it stops working. Whenever I pickup the phone, instead of hearing the dial tone, I hear a busing beeping tone, like a machine gun is firing. :) However, from asterisk console, I do see a a OffHook/OnHook message, but whatever I dial in the phone keypad seems not

Hi, I want to do a scripted 'restart when convenient' on a daily basis. This used to work, but since i've upgraded to Asterisk 11.7 it seems it's never convenient to restart the server. My question: how can i tell *why* it's not convenient to restart the server? It used to be some colleague left the receiver OffHook or something like that, but even when i'm fairly

The FXO lines on my TDM400 are connected to PSTN lines in Israel. As far as I know, the lines around here have disconnect supervision (I've seen some other Israelis on this list, anyone know for sure?), because it's worked on Dialogic cards, which reported hangup, not busy detect (while when I connect a Dialogic card to a PBX, I have to measure the busy signal's frequency/cadence or

Hi all, I would like to make a script/program that would be able to show lots of status information from my analog FXO lines (and FXS lines in the near future). Example of interesting status information: - Hook status: is there a call being made with that zap? - Voltage status: cable connected, voltage values (if possible), line ringing? - RX/TX Volume status I'm using a TDM400 card with

Hi, We are having a problem with asterisk detecting that an analog ext has been put down. This seems only to happen after a number of calls have been made. We have an FXO port (TDM400P with FXO module) connected to our PBX and are using this to test asterisk prior to rolling our for our small office. What happens is that we make a number of calls to this ext which 1st rings a phone (FXS)

I've installed Grandstream GPX-2000 phones and have successfully enabled one of my buttons to use Asterisk BLF for an extension. I can tell when this extension is available, is being rung, or is on the line. I'd like to do the same for my Zaptel channels, to be able to see when a line is onhook, ringing or offhook. I tried the following but alas, it doesn't seem to be working: