similar to: x100p offhook/onhook states

My TDM400P w/ 4 FXO cards seems to have trouble with onhook/offhook switching. It dials perfectly, but does not seem to be changing the onhook/offhook state appropriately. It changes sometimes, but it's not really reliable. For example: When I booted the machine, it started as onhook. It remained "onhook" through the entire first call (which was silent on both ends --

> -----Original Message----- > From: Jacqueline Lee [mailto:jlee@isdomaininc.com] > Sent: Friday, September 23, 2005 11:46 AM > To: asterisk-users@lists.digium.com > Subject: channel offhook state > > > We are using a digium card (TDM400) with asterisk for our access to the > PSTN. Initially when the server starts, all the zap channels on the card > are in the

Happens quite often. X100P FXO card puts the PSTN line offhook, so that no calls go out or come in. The outside callers get a busy siganl while inside callers cant dial PSTN. Its a DELL optiplex P3 128MB ram 500MHz processor. Here is some more info: (see the zapata.conf in the end) Please direct me where to look for problem. Thanks!!! ======================================== pbx1*CLI> zap

Does anybody know if there are any external telephone-keypads for sale anywhere? (containing the keys 0-9, *, # and onhook/offhook would do) I am looking for a keypad to control a softphone and would prefer the controls to be in the physical world instead of as a window. Sincerely, Markus Hakansson

Hi, the new Grandstream release for the ATAs allows the setting of the FXS impedence, the Onhook Voltage and the Polarity Reversal. Anyone know how these should be set in Germany? -- Best regards Peer Oliver Schmidt

Hi, I have a analog phone connect to a WCTDM card. It used to work fine. Now recently, after several conf change and power restart, it stops working. Whenever I pickup the phone, instead of hearing the dial tone, I hear a busing beeping tone, like a machine gun is firing. :) However, from asterisk console, I do see a a OffHook/OnHook message, but whatever I dial in the phone keypad seems not

Hello, In my quest to figure out the source of the random echo on our shiny new asterisk install, I have been using ztmonitor on the TDM400p channels for the good part of today. I have 2 TDM400p cards with 8 FXO modules and 6 pots lines connected to them (last 2 channels are unused but configured in zaptel). Even when the lines are onhook, the Tx values settle down to 0 but the Rx values still

>Asterisk and it works fine untill the following >situation: > >- one of the telco lines occasionally becomes mute after call is completed, would not provide dial tone, (not sure about ringing on that >line) - both via old and new PBX. >- zap show channel <n> would show that line as 'Offhook', though no telephone is off hook. > >If physical line would be

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

I finally got my X100P working and now I have a question. I have several Skutch phone line simulators. My X100P works as expected with both a POTS line and an analog PBX port, but when I use a phone line simulator it doesn't answer the line. The phone line simulator doesn't power the line until the phone set goes offhook. Asterisk shows the RED alarm and then the alarm clearing but never

I tried implementing my * and it didn't pass the spouse factor at this time. I wanted to hook it up for outbound only at this point to get a better handle on the dial plans and the echo problem. I thought this might have been done before as a natural part of testing - but maybe not. In wcfxo.c I found this: if (!wc->offhook && !wc->ringdebounce) { if

Hi folks. I am using a X100P card and after some random amount of time of correct operation, say 8-20 hours, the card starts acting up and producng horrid sound quality which is all broken up. All other channels appear to work fine. One thing I noticed, is that "zap show channel 1" always shows the "Actual Hookstate: Offhook" as soon as the telco line is plugged in. Is this

Hello I was wondering whether anyone has managed to get an X100P card to receive Caller ID information in the UK (connected to a BT line)? I guess that it probably won't work at present because BT sends the CID information before the first ring - hence there is no event to wake up the channel. I can hear it using ztmonitor, but it is far too soon for anything to receive it. According to the

Hi I have the X100P card which as to sockets (LINE - for fxo line ) and PHONE (to connect a n analog line) This card is setup as fxs_ks I was getting dial tone but suddenly no Dial Tone....Help appreciated.... When I try to route the Call using - Dial Zap/1) to this FXO Line I get this error: ------------------------------------- linux*CLI> -- Executing

Hi, I have an AsteriskAtHome installation with two X100p clones. Everything has been apparently fine for 5 weeks of use or so, but today, I decided to do some tweaking of my echo cancel parameters, and I realized that all along, one of my cards has been unavailable for outbound calls for some reason. Most of my calls go out one card, which is connected to a Vonage ATA. That is working fine.

Hi! The X100P is working - partly. I can make outgoing calls. But the card has got a problem detecting incoming calls. Even in verbose mode I don't see any hint that the card detects a call. At the moment I'm using the card behind my old ISDN telephone system. Could it be a problem with the line voltage? Can I adjust anything when loading the kernel module? Bye! Michael

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hello, Caller -> PRI -> SIP -> application. If application goes offhook right away, dtmf/audio works fine in both directions. If application, before going offhook (sending OK) plays a message and wants dtmf/voice from the caller, then caller can hear this message but his dtmf/voice don't reach application. Any way to configure it? Thank you. Alex Zarubin -------------- next

Hi, We are having a problem with asterisk detecting that an analog ext has been put down. This seems only to happen after a number of calls have been made. We have an FXO port (TDM400P with FXO module) connected to our PBX and are using this to test asterisk prior to rolling our for our small office. What happens is that we make a number of calls to this ext which 1st rings a phone (FXS)