similar to: chan_zap.c:6181 mkintf: Unable to get parameters

Now I have this errors When I lunch this command I got modprobe wcte11xp This error: Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for wcte11xp And when I lunch this command ztcfg -vv I got these: Zaptel Configuration ====================== SPAN 1: CCS/HDB3 Build-out: 0 db

I've put a t100p in our * server and I'm having trouble configuring it. It is directly connected to an Adtran TA 750 channel bank with two FXO cards (8 analog incoming lines total). I'm able to insmod and modprobe both zaptel and wct1xxp with no trouble, but when I start * with /usb/sbin/asterisk -c I get the following output: [root@rosella root]# /usr/sbin/asterisk -c Asterisk

Hello, I was trying to configure 2 Digium X100P-Card compatible FXO cards. Everything went OK up to starting Asterisk, the following error occures while parsing zapata.conf: Parsing '/etc/asterisk/zapata.conf': found Mar 27 16:24:20 ERROR[1075656544]: chan_zap.c:5196 mkintf: Unable to get parameters Mar 27 16:24:20 ERROR[1075656544]: chan_zap.c:7162 setup_zap: Unable to register channel

Hi! The encoding, decoding and recoding cost cpu time, that's sure. But does this time differs much depending on the used codec? Is - for example - a G729 faster than a GSM codec? Bye! Michael

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

Hi all. chan_zap not compiling, yes yes I know this sounds trivial but here me out... This morning I decided to upgrade to Asterisk 1.4.2 and Zaptel 1.4.1. I successfully installed zaptel 1.4.1 and the card is picked up and correctly configured. ztcfg shows the following: [root@zion root]# ztcfg -vv Zaptel Version: 1.4.1 Echo Canceller: MG2 Configuration ====================== Channel

Hi!I've a problem with asterisk,it doesn't start..it's stopped..I used the amportal start command and this is the result: SETTING FILE PERMISSIONS Permissions OK STARTING ASTERISK Asterisk ended with exit status 1 Asterisk died with code 1. Automatically restarting Asterisk. Asterisk ended with exit status 1 Asterisk died with code 1. Automatically restarting Asterisk.

I've just finished updating my Asterisk to the CVS version. Unfortunately, chan_zap won't load anymore. The hardware has not changed and the config files have not changed. I can re-install the two packages back and forth. The old one will still work. The new one won't. I tried updating to a brand-new zaptel and wcfxo modules, with no difference. This has got to be the most

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

Hi! I want to connect my asterisk system to the PSTN. Now I'm thinking about using an analog modem as FXO device. Which modems do run? How is the voice quality? (I looked into the wiki, but on <http://www.voip-info.org/tiki-index.php?page=Asterisk%20hardware> no regular modems were mentioned. Or should I use a special FXO-card? I don't want to spend 99$ for such a thing but

Hello I've been googling for this message, but can't find why Asterisk sends a warning. The configuration files look similar to http://www.voip-info.org/wiki/index.php?page=Asterisk+config+zapata.conf.sample It's a TDM card with just one FXO module on it, and I connected an RJ11 cable to it from the wall plug: # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

I'm trying to figure out how to start *..... Rh7.3,CVS,TE410P,TA750 If I just try the way the docs spell it out "/usr/sbin/asterisk -vvvc" it fails...... /var/log/asterisk/messages Oct 3 22:23:34 WARNING[1024]: File chan_zap.c, Line 610 (zt_open): Unable to open '/dev/zap/channel': No such device Oct 3 22:23:34 ERROR[1024]: File chan_zap.c, Line 4930 (mkintf): Unable

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

I'm running latest asterisk and zaptel, I have loaded wctdm and lsmod shows that it is in the kernel. I have configured the FXS and FXO ports on my TDM400P, and ztcfg shows both as configured with no errors. When I start asterisk I get the following error: Mar 13 14:07:41 WARNING[10958]: loader.c:325 __load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_pickup_cal. A

hello, i have a problem starting asterisk with one x100p digium and two hfc chipset isdn cards with bri-stuff.0.0.2. "ztcfg -vv" shows me a this info: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03:

I'm having a problem defining my channels Here is my zapata.conf ----------------------------------------------------------------------------------------------------- ; Zapata telephony interface ; ; Configuration file [channels] ; rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down