similar to: How to get transfer and blind transfer on 7905

I have a few Cisco 7905G phones and I having a little trouble configuring them. They are working with Asterisk. I'm able to get the sip image loaded, but I can't get the phones to blind transfer. Does the Cisco 7905G Phone use XML Services? If you are using the 7905G phone, would you post any of your configuration files so I can try and figure out where I'm going wrong? Thanks for

I have been able to upgrade my Cisco 7905G phones to the SIP Image without any problems, but I just got a 7960, and I can't seem to get to the settings so I can upgrade to a SIP Image. When the phone boots up, it says Configuring VLAN, Configuring IP, TFTP ????..., then Protocol Application Invalid. I noticed on the wiki page "Firmware issues on 7940 - 7960"

Hi I'm having 2 strange problems (or rather I am doing it wrongly!) ..need some help.I am working on trixbox 2.6 with Asterisk 1.4.22 1. I've a Queue with dynamic agents (ampextensions=deviceanduser mode in amportal.conf), some of agents when they punch in the wrong UserID - they still get logged onto the Queue as a result many of them complain that they don't receive calls on

List, Having a little trouble with the following. Let me prefix by saying I have blind transfers working from the following setup. Inbound call [from-zap] (SIP/sv0071iv) answers. Zaptel -> Asterisk -> SIP extension SIP extension then blind transfers [from-sip] --- SIP extension -> Asterisk -> Zaptel During this whole process, the original channel off the trunk (lineside T1) is

Hi BK - >> The blind transfer does not work. >> >> The way we try to blind transfer a call: >> 1. answer the call >> 2. press transfer >> 3. press blind softkey -> the display shows "Blind transfer to:" and >> cursor is in the second line >> 4. enter the number -> when we enter the second digit of the number >> the

Hello, Sorry for a bit of a newbie post but we all had to start somewhere right .. I'm wondering if someone can briefly explain the difference between blind and attended transfers and why they would generate two very different CDR entries.? From my own research, it seems that transfers are both ultimately a SIP REFER and thus seeing two different CDR entries just confuses me further.

Good morning folks, I am quite new to Asterisk but have successfully set it up with some BRI lines, Cisco 7940/7960, queues, voicemail, XML stuff and the flash operator panel. When playing with the manager API to get some stuff integrated within our systems, I stumbled across the Redirect command and the way it is working. Generally, there is a difference between Transfers and Blind Transfers of

HI callee side blind transfer is failed in 1.8 but caller side blind transfer is succes,Transfer doing by refer method,please help me on this Nikhil

Guys, this is a weird question but has anybody disabled the blind button that appears on polycoms or know if you can disable the use of blind transfers on polycoms to make any transfer attended? Thx!

Hi, Am running 1.4.18 at the moment, and am trying to implement inline blind transfer. I have : [featuremap] blindxfer => *6 ; Blind transfer in features.conf And in extensions .conf under [globals] : DYNAMIC_FEATURES=automon#blindxfr So what am I missing ?? Have read through http://www.voip-info.org/wiki/view/Asterisk+config+features.conf Thanks,

Yes, After call transfer,I don't want to be media go through Asterisk. Is it possible ? Thanks, Karun. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com]On Behalf Of Dameon D. Welch-Abernathy Sent: Thursday, August 12, 2004 12:07 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Blind Call Transfer using

I want to setup a blind transer for auto forwarding to SIP peer. I have context forwarding looks like this in extension.conf [forwarding] ... exten => 511,1,Dial(SIP/sip_proxy-out) ... This will do the re-invite, which is attendance transfer maybe. But I want a blind transfer by REFER method. How can I do that? I know that the transfer() function may be able to do that. But I don't know

I know this isn't an asterisk thing, but since the recommendation to get one came from here I figure lots of people out there have one. I read the docs, and it says that in order to do a blind transfer I should hit "flash", then dial "*__" then the number. Now, how on a normal phone do I dial "asterisk underscore underscore"? Can someone tell me how doing a

I have a Cisco 7960 phone. I cannot seem to use the settings button to get into the phone to change the TFTP server. I've set up a DHCP Server, TFTP Server with the same address, and the phone requests the address of 0.0.0.0, the server offers the address of 192.168.2.2, but the phone seems not to take it. I have no action on the TFTP side. So, since I can't seem to server the phone

Hi, I'm using Asterisk@home and am having trouble using the conference bridge that comes built in. We're using Polycom phones. When we transfer the first person into the conference room (e.g. 8101) , they get into the room fine. When we try to transfer a second person into the conference room, they get dropped as soon as we finish the transfer. This is using Polycom SoundPoint 301

Hi all, when doing a blind transfer using the keys defined in features.conf, we hear a confirmation of the attempt to blindly transfer, followed by an invalid extension message. The console says this: [Jun 4 22:30:31] VERBOSE[11301] res_musiconhold.c: -- Started music on hold, class 'default', on SIP/570-00000006 [Jun 4 22:30:31] VERBOSE[11301] file.c: --

Hi, I can't get Asterisk to save CDRs for calls transferred via SIP blind transfer. My extensions.conf: [globals] __TRANSFER_CONTEXT = transfer [common] exten => 123,1,Playback(demo-congrats) exten => 123,n,Hangup() exten => _0X.,1,Dial(SIP/${EXTEN}@PSTN-GW,60) exten => _0X.,n,Hangup() exten => i,1,Hangup() exten => h,1,Hangup() exten => t,1,Hangup() [transfer] exten

Hello Users, We have Thirdlane Multi tenant PBX system in production. Asterisk version is 1.6.2.15. Attendant transfer is working, but blind transfer is not working with Grandstream (gxp-2000) phone. We have read from google that it is a bug in Asterisk 1.6.2.15. We saw the below links: <http://www.odesk.com/leaving_odesk.php?ref=http%253A%252F%252Fwww.freepbx.o

Hi, Is it possible to "regret" blind transfer while its ringing (not answered)? Thank you! Best regards HB

Hi all, Is there a way to tell which extension transferred a call in a blind transfer? Sorry if it's a basic question, but I haven't seen an answer. ${CALLERID(num)} still holds the outside party caller id (which it should), but I'd like to the extension number of the extension that transferred the call. Any suggestions? Thank you, -- Warm Regards, Lee