similar to: Cisco gateway help needed

All, I need to run this by everyone and see if someone has any idea's. I have a asterisk server setup and currently am receiving the inbound calling number where the name should be. My setup is.... One pri terminating into a Cisco 2431 router Sip messages from the Cisco get sent to a asterisk server linksys ata's a each remote end. I can receive the calling name if the call originates

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

Hi Everyone, I'm new to asterisk and trying to get together the hardware to run a few POTS phone extentions and one or two POTS lines for starters. For these low port counts, I could just go with FXS and FXO cards, but... I can get a Cisco MC3810 with a mixture of FXO and FXS ports, the MC3810 comes with a built in ethernet port and I believe it does SIP too... Will this mean that I

Has anyone got a Premisys Slimline channel bank working with a Cisco AS5400 or similar? I'm not sure if my unit is bad, or what. I'm using FXS Loop Start. Calling the port connects immediately without ringing the attached phone. If I pick up the phone, it's connected and I can talk to the caller. Hanging up has no effect. I can see the bit transitions (0101 to 1111 when I go

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

Has anyone here successfully gotten a cisco MC3810 talking with asterisk? I am getting the dreaded - Got SIP response 400 "Bad Request - 'Malformed/Missing URL'" back from xxx.xxx.xxx.xxx If you've gotten it to work you can feel free to email me off list. If your willing to share config's that also is a definate plus. Thanks, --Tammy

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Hello Since I am getting a bit concerned about the SCO vs IBM issue, I was wondering if can I can setup Asterisk on FreeBSD is it supported ? Are drivers for Digium cards available on FreeBSD ? Thanks Ajit ----- Original Message ----- From: <asterisk-users-request@lists.digium.com> To: <asterisk-users@lists.digium.com> Sent: Wednesday, July 30, 2003 3:05 PM Subject: Asterisk-Users

Hello, I'm trying to run an ATA behind a NAT device, and am confused on exactly what the qualify config option does, other than send NOTIFY packets. Outbound calls work fine, but inbound calls do not go through. With qualify=yes and nat=yes, my show sip peers looks like: 7771111001/7771111001 10.0.0.10 D N 255.255.255.255 1222 OK (36 ms) So, it has established a

I have asterisk 1.6.2.11 talking to a cisco 1760 running ipvoicek9-mz.124-25b. whenever a call goes through the 1760's FXO or FXS (in or out) there is a 915 second maximum call time due to asterisk hanging up the call because of a "critical packet" being missed. I read doc/sip-retransmit.txt and I don't see anything there that is helpful to my situation - the asterisk box is

If you have a PRI terminated in a Cisco router talking SIP to * and would be willing to share your Cisco config, please respond. Also, I would be interested in knowing what version of IOS you are using. We are using an NM-HDV in a 3640. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

Hi, I had previously posted about connecting an AS5300 to * via SIP/H323. I got it to work via SIP, but only 1 call at a time would work, and if a user from the * side hung up, the cisco would'nt catch the hangup. I an now trying to hook up to the cisco via E1, with a Sangoma A101 card in my * box. I would like it such that I call from * via E1/PRI to the cisco, and call out via R2 to

How do you specify in a tablegen pattern that all destination registers are also source registers? I know I could just duplicate them, but I was wondering if there was a way it could be done without doing this. Basically an inplace operation. So for example, take a hypothetical swap w/ sqrt. if I had swap $ds0, $ds1 which swaps ds1 and ds0 and applies sqrt on the registers afterwards. Micah

Heh guys, I just received a T400 card, I've been using a T100 for a little while, and it works fine when using a raw channelized T1. I'm relocating my asterisk machine, and PRI's will only be available, haven't found any good config info for PRI's, can someone point me to PRI config info, or let me know what changes I need to make in order to bring them up, I imagine,

Hello, Has anyone experienced a segmentation fault in asterisk for using G729 against an AS5300 in SIP ? I'm having this problem. Also, any other codec I use gives me incompatible media (can be read in SIP DEBUG messages). AS5300 configured for multiple codecs, so is Asterisk. Tried G711u/A G723 and G.729. Any clues ? Regards, Jorge A. Info: Asterisk ver 1.0.7 stable Using AMPortal

Hi, I am experiencing one-way audio from: SIP Device ----> Asterisk -----> Cisco 7200 The Cisco 7200 has a VXE+ card that will allow you to do SIP. I can pass audio from SIP Device to Asterisk through the Cisco 7200 to the other end, but the Cisco 7200 does not return any audio back to the SIP Device or Asterisk, it seems. I have tried upgrading to 12.3T IOS version, but no

hi, i have some newbie questions about channel banks. i have an adtran act-1241 sitting around. it accepts D4 modules, and it contains a number of e&m cards. first of all, how does this thing work? a t1 contains 24 channels, and i noticed that the channel bank has space for 24 cards. what do these cards do? what are their outputs? the ones that are in there have some outputs on the front

Hey All, I'm just daydreaming here.. but what's the status of SIP-T in Asterisk? I haven't been able to find a whole lot of info on SIP-T but seems like just an extension of SIP. Right? Now if I had a PSTN Gateway (that is a SS7 gateway) that supported SIP-T, could I signal * with SIP-T from it and have asterisk utilize MGCP to sieze a particular DS0 on a remote DS1? Hmm.. What am