similar to: calling an iaxy

Hi All; I need to buy one IAXy device, but I discovered that it supports only g711 and ADPCM codec, so I was wonder that it does not support g729 or GSM?! Anyway, what is that ADPCM and how much it consumes bandwitdh? Also, asterisk support such codec? What its name in the configuration? Any advise? Regards Bilal

Hi everyone, I'm using the IAXy boxes and i'm having some trouble when I use it with the ADPCM codec. When I use the ADPCM codec only one person (out of the two of the conversation) is able to hear the other, but when I switch to ULAW codec everybody can hear the other. The ULAW codec is too heavy for my bandwidth (64Kbits/s) and its sounds choppy, the ADPCM codec sounds good but only

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

I have somewhat miraculously got my server to stay up for over 24 hours now. I was at my remote location, however, and I can't make calls that used to work find. I get the following messages. I get a brief bit of good sound and about the time I see the message "Ooh, voice format changed to 4" all further sound stops. The machine seems to be stalling, but I have noload on both oss

Hi everyone, We are using the IAXy boxes and Asterisk over the internet and I was wondering if Asterisk can do a codec translation during a call in order to lower the bandwidth that the comunications consumes? I mean, the IAXy boxes only support the ADPCM and uLAW codecs, but for a certain number of calls our bandwidth runs out, then I think if Asterisk can convert the signal that comes in ADPCM

Hi! I'm really hope you can help me solve a little mystery, the mystery is probably just my misunderstanding ! sorry... I've got an iaxy talking to my * box which connects to two providers. I'm running the stable release of the pbx. The only thing is that when dialling from the iaxy the ringing tone isn't heard while calling someone - you just hear silence then, they either

I haven't seen much activity on the list concerning Digium's IAXy standalone FXS device. Are they worth $100 ? Do they integrate well with * as an extension's FXS ?

I'm trying to force GSM when I call on certain extension but I'm getting connected with "ulaw" Which is not suitable when bandwidth is low and slow. my phone is iax-322 in iax.conf [iaxy-322] ... disallow=all allow=gsm allow=ulaw allow=alaw [zoiper_kathy_old_phone] ... disallow=all allow=gsm allow=ilbc allow=ulaw allow=alaw allow=speex I've define "allow=gsm"

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

I can't seem to get this device to grab an ip from dhcp. We have a working dhcp server (unfortunately it is on Windows), but I don't show any leases requested by the iaxy. Anyone have any ideas? The ethernet and phone lines are plugged in before the device is powered. Thanks, Erik

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

Hi, Has anyone got faxing working via an IAXy? I'm having trouble getting it working with a fax machine here. The IAXy works fine, I can make incoming/outgoing calls via it, however our PDQ takes a few redials to get data over to the dialled party, and faxing doesn't seem to work at all. I have turned off all the echo cancellation stuff, just in case that was an issue. Anything I

In features.conf, I have uncommented the transfer features under feature map, but I still cannot transfer using a POTS phone on an IAXy adapter. I think I am missing something here.... Any help is appreciated. Here is features.conf: ; ; Sample Parking configuration ; [general] parkext => 700 ; What extension to dial to park parkpos => 701-720 ;

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or