similar to: REGISTER timeout problem with Broadvoice

All, I signed up for a broadvoice BYOD plan over the weekend (very excited about their offering) and after about an hour I had asterisk registered and was making in and out bound calls. However, the next day (without changing anything) I couldn't call in or out and haven't been able to get it going again. I can connect using a softphone (X-Lite) and make calls in and out

I had my asterisk configuration working very well with broadvoice, but it stopped working this afternoon. I plugged the Cisco 7960 phone I used for my origional signup (just a few days before they offered generic BYOD) and it works fine. I did notice it seems to do all of its comunication through proxy.broadvoice.com (I used tcpdump). I have never contacted broadvoice about using asterisk

Hi all, I just upgraded to Asterisk 1.4.18 a few days ago and I don't use Broadvoice TOO often, however I have a Vermont number with them and so my mother in law calls it to talk to my wife once in a while, so that's why it took me so long to notice it wasn't working. Anyway, when she calls she gets a busy signal (as I've tested when calling it from my cell). When I enable

I'm getting a couple strange things with asterisk on Broadvoice. It works fine currently for inbound and outbound. Everything is registered, its perfect. My problems currently are: 1) After 20 minutes audio out to broadvoice goes away 2) After about 3 hours my registration attempts to broadvoice time out and the only solution is to switch to a different proxy which subsequently works.

Ok we have found a better solution. Put everthing back the way it was and make sure that you have this line in your general section of you sip.conf file: srvlookup=yes We have added a SRV entry in the correct place now. So everyrthing should go the correct servers. -james --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.726 /

Hello all, When I call the Broadvoice number all is good. When I try to call out through DISA on my broadvoice line i get the following: Executing Dial("SIP/147.135.0.129-0815bc60", "SIP/16037862111@proxy.bos.broadvoice.com|30") in new stack -- Called 16037862111@proxy.bos.broadvoice.com -- Got SIP response 480 "Temporarily Not Available" back from

Since Thursday evening my asterisk box has been failing to register with broadvoice. I haven't changed any of my config files in the last week. Can anyone suggest anything? Asterisk is reporting: *CLI> Aug 28 16:15:17 NOTICE[6150]: chan_sip.c:3914 sip_reg_timeout: Registration for '703XXXXXXX@147.135.8.129' timed out, trying again -- Got SIP response 404 "Not found"

I have been going crazy with this also since Sat. Our server was working perfectly with BV but will now not place calls to BV. Incoming from BV works fine. I felt sad rebooting it today, it had been running for almost 200 days! Here is my error message from the console... Notice I am running today's CVS Connected to Asterisk CVS-03/08/05-14:32:39 currently running on com (pid = 1624)

I've tried everything with the * box after this weekend. I have read every document on the problems people are having with them after this weekend as well, but none of them address my problem. I checked my settings in my sips which I have below as well, I have changed the host file a few times, but this was new to me and I never had modified it before. I have and the same results

Hello, I have two broadvoice accounts. Lately, very often my broadvoice accounts are in unregistered state. When I log into asterisk I see: voip*CLI> sip show registry Host Username Refresh State sip.broadvoice.com:5060 yyy@s 120 Request Sent sip.broadvoice.com:5060 xxx@s 120 Request Sent xxx and yyy are my ohone numbers, when I do tcpdump on my router, I see only packets comming out my

I have configured asterisk with the AMP php configuration utility. I am able to make outgoing calls through broadvoice but incoming calls are sent to BV's Voicemail and never actually enter the IVR. When I show sip debug info through the asterisk prompt it actually reads the incoming call from BV but then issues a busy signal sending the call to BV's voicemail. I also modified

I just signed up for the BroadVoice service a few hours ago, but for the life of me I can't get any incoming voice. The incoming connection is fine as it rings my extension from outside, but I can't hear anyone talking. Outgoing voice is working fine though. I've been looking through the archives, but I haven't found a solution to the problem yet. I even tried another router

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

Hello, Please forgive me if I'm repeating this post. I have searched and looked for similar problem with a solution but have not see a similar one. My outgoing SIP and other channels work fine but the incoming/inbound SIP call goes straight to Broadvoice voicemail. I see that Broadvoice is registered when I look at the SIP registry. I have turned on SIP Debug and it is below. Anyone know

Egad, not again with Broadvoice! Anyhow, I recently installed AAH and configured my TDM11B and got that and some SIP phones working. I still have some issues to work out, etc, but my current problem is Broadvoice. I have checked out all of the online resources, including the recent list exchange about the recent changes made by Broadvoice. However, the one thing I have found to be consitent in

Is anyone else experiencing 404 errors on outbound dial with Broadvoice? I've followed the instructions posted by Broadvoice to configure sip.conf, and inbound calling works fine. Every time I try to dial out, I get a 404 "Not Found" error. Here are the relevant sections from my configs. sip.conf: context=broadvoice-in register =>

Hi all, I've been trying to use BroadVoice as a SIP service provider. They don't officially support * but are helpful when it comes to answering questions for setup parameters. They claim they have no firewalls or access lists that need to be set up so I can get access to their servers. However, something's still not quite right when I use the parameters. It looks like our Asterisk

My SIP seems to be configured correctly as I can dial out and my minutes show up on my broadvoice bill, but whenever anyone calls my broadvoice # inbound they just get a busy signal. I dont get anything in the logs saying anything came in from broadvoice at all. Has anyone had this/simmilar problem with inbound from Broadvoice? Any suggestions? Thanks Neri -------------- next part

All, I have been fighting with my dialplan for hours now, and google searches talk lots but offer nothing in terms of explication for this. I have my SIP peer set up and working with Broadvoice: [sip.broadvoice.com] type=peer user=phone host=sip.broadvoice.com fromdomain=sip.broadvoice.com fromuser=5555551234 secret=password defaultuser=5555551234 insecure=port,invite context=broadvoice