similar to: IAXy - anyone using them yet?

I am attempting to get fax detection to work. I am using a NETjet-s card under ISDN4Linux. Asterisk does not seem to be detecting the fax tone. I have tried following as a test: [MainMenu] exten => s,1,Answer exten => s,2,DigitTimeout(3) exten => s,3,ResponseTimeout(5) exten => s,4,Background(Welcome) exten => s,5,Background(MainMenu) exten => fax,1,Dial(Zap/1,,d) [FaxTest]

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

Anyone using this 110-220v 9v 1500ma supply? If so, which DC plug adapter does the IAXy need? A friend brought the wall wart over here for me but she said you get one plug free and she didn't know which one it took. Does anyone here know? http://www.radioshack.com/category.asp?catalog%5Fname=CTLG&category%5Fname=CTLG%5F009%5F001%5F001%5F003&Page=1

In features.conf, I have uncommented the transfer features under feature map, but I still cannot transfer using a POTS phone on an IAXy adapter. I think I am missing something here.... Any help is appreciated. Here is features.conf: ; ; Sample Parking configuration ; [general] parkext => 700 ; What extension to dial to park parkpos => 701-720 ;

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

I can't seem to get this device to grab an ip from dhcp. We have a working dhcp server (unfortunately it is on Windows), but I don't show any leases requested by the iaxy. Anyone have any ideas? The ethernet and phone lines are plugged in before the device is powered. Thanks, Erik

Hello-- In the interest of Symmetry, does anyone else in the world see any need for a device like the IAXy (or the SIP ones from other manufacturers, like the ATA186), but one that presents an FXO interface instead, so it can be connected not to phones, but the PSTN? murf

Hi, hoping that experienced hands will quickly show me the right way: after a fruitless web search i am turning to this list with my rather elementary question: is there any other way to communicate with the IAXy besides using special utility software that needs to be compiled under UNIX? Here is the story: about two months ago, after some not very satisfactory attempts at using SIP (my phone

I've heard comments about the instability of the IAXy (loosing IP, locking up, etc) . I want to deploy some, in a remote site. The comments on the instability suggest that the simplest approach is to power-cycle them when you have problems. The IAXy would only be in use from 3PM to 8 PM. My potential simple solution is to have a timed power brick (like what you would use for a block heater)

It's happened before, cleared up and now it happened again. The IAXy, working for a total of about 6 months. Symptoms: Registered with asterisk and even receives calls (the LED shows it's ringing) but phones connected to it are dead. Same phones work connected directly to the phone line. Cable swapped out, no difference. Endless re-provision (with normal looking output) and power

I have a couple of devices that need an analog modem to communicate outside of our Asterisk system. Most FXS gateways don't seem to support this... I have a stack of Sipura 2002's that are, AFAIK, worthless for this purpose. I've heard that Digium's IAXy FXS will work with modems, but I can't find any reference to that in their documentation. There is also the

Hello, Please be conscious of Digium's bandwidth and use a Mirror when downloading 1.0. I have mirrored the tarballs at: ftp://ftp.nacs.net/asterisk/ Direct links: ftp://ftp.nacs.net/asterisk/asterisk-1.0.0.tar.gz ftp://ftp.nacs.net/asterisk/asterisk-sounds-1.0.0.tar.gz ftp://ftp.nacs.net/asterisk/libpri-1.0.0.tar.gz -- Vice President of N2Net, a New Age Consulting Service, Inc.

I was just browsing Digium's web site and noticed they are taking orders for the new IAXy. Has anyone purchased and tested one of these yet?? I have thought about buying one for testing, but want to make sure it isn't going to be a flop like the last one. Robert

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04: