similar to: UK (British Telecom) Caller ID again

Hi, I'm currently running asterisk 1.0.9-r1 and zaptel 1.0.9_p1-r1 (the current gentoo ~x86 versions), with the UK CallerID patches from http://www.lusyn.com/asterisk/patches.html applied. The Zap interface itself seems to work fairly well - although it's a little quiet, there is no echo. Unfortunately, there's also no CallerID. My zapata.conf is as follows: [channels]

dear all, i am looking to enable CALLERID on an Asterisk system comprising a X101P FXO interface connecting to BT PSTN in the uk seems this is supported by the interface but there seems to be varying information on how to enable it in zapata.conf 1. usecallerid=uk 2. ukcallerid=yes being two of the configuration statements offered TIA GT

Hello, I have recently purchased a TDM400P card with one FXO expansion card, and I'm having problems. The card does not pick up incoming calls. Asterisk detects the ringing line and rings various SIP phones as required. When a sip phone answers, the sip user hears nothing and the PSTN user continues to hear ringing. Here is the asterisk output for an incoming call:

Hi, I've got a problem with my asterisk set up which has been going on for a while (months). I'm currently running 1.2.7.1 on a gentoo box with the topology below: +-----+ PSTN ---------+ * +------------- Service Provider (wctdm400p) +-+-+-+ IAX | | | | FXS --+ +-- SIP (cisco 7940)

I was curious to read the following in the "Guidelines for Rd files" at http://developer.r-project.org/Rds.html: "For consistency, aim to use British (rather than American) spelling. (NB: British spelling often uses -ize as in `capitalize'. The view of spell -b of British spelling is a flawed American one. There are English/Scottish differences

Hi folks, With thanks to Alison Keenan (another Alison!) for the voice, Chris Bagnal for converting from 44k wav to sln and finally Terje Elde for debugging my HTML code, the British English files are now ready for download. They can be got from http://www.enicomms.com/cutglassivr/ Thanks and don't forget to practice safe IAX ;-} Mark -- Mark Phillips <g7ltt@g7ltt.com>

i belong to india. i am making pbx using sangoma fxo card. i want that when ever call comes to my PSTN line i should see the no from where call is coming. so i have to configures chan_dahdi.conf according to my region. i checked dahdi.conf and in that they have mentioned for india

some of my validation error messages contain a pound sign (the British currency, not #) however, this get''s shown as a question mark in the view. i can get round it by using the html reference (&pound;) instead of the literal character, but it seems a little counter-intuitive to handle this in the model... isn''t it view related? any suggestions? I''m developing

The Stern Environmental Review, a British Government Report into tackeling global climate change has been published online. Leader page with presentation and speaking notes :- http://www.hm-treasury.gov.uk/independent_reviews/stern_review_economics_climate_change/sternreview_index.cfm The Stern Review Report :-

Hi All, Having searched the archives, I can see there has been much discussion at various points regarding capture of caller id information from good old BT. If I understand correctly, it seems that not only do the drivers not currently support it, but my X101P possibly/probably can't do it anyway due to hardware? So, that leaves me with the modem route, which seems more and more unlikely,

I am on UK Cable (Telewest) will this callerid patch work with the cable caller id? Thanks. Paul.

Hello, All :) Regarding to incoming caller ID on PSTN line, which one is best supported by asterisk: is it FSK ETSI or FSK US? I bought some caller ID converter hardware (convert DTMF to FSK and vice versa) but still asterisk can not detect it. The converter has a switch FSK ETSI or FSK US This is what I put in /etc/asterisk/chan_dahdi.conf ... cidsignalling=bell cidstart=ring ... If after

Hi, I've got an x100P and I'm able to dial out and make phone calls with it ok but I just want to set it up to answer the phone and be a simple answering machine but it doesn't seem to want to answer the phone. I keep getting this: on the console when the phone rings: -- Starting simple switch on 'Zap/1-1' Nov 28 08:55:09 NOTICE[29298]: chan_zap.c:5458 ss_thread: Got

I have my peers registered to SER.asterisk seems to be sending mwi for the peers seen in the sip show peers CLI command. i have my ser server registered with asterisk as a type=friend and all clients register to ser.how do i get mwi to work for these clients registered to SER. Thank you, -AA

I have a line from BT (UK) connected to my asterisk system, on a TDM400P. I am able to see either distinctive ring cadences or caller ID but not both. If I try to enable both, all drings show up as 0,0,0. This is a pain because, if I make a call out over that line and the number I call is busy, I can elect to camp on it (ringback), which results in a different cadence of ring when the called

Hi, I have a weird situation where I have a noop command putting the callerid of the caller on my asterisk console so I know who is calling as a test, but it is putting the callerid of my extension in instead of the callerid of the incoming line. My /etc/asterisk/zapata.conf is [channels] context=default ;switchtype=national usecallerid=yes cidsignalling=v23 cidstart=polarity hidecallerid=no

Hello... I have a big problem with asterisk. Every time i make a call asterisk does not bridge the zap channels. The zap channel from which i'm calling remains in state:ring and applicaton:dial and the zap channel with the external line configured remains in state:dialling an Application:AppDial. Zap/20-1 agentie s 1 Dialing AppDial (Outgoing Line) 09399 (None) Zap/9-1 int_omg 09399 5 Ring

Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels]

Hi all, I've been running Asterisk with a TDM400P for about 6months, no problems. 2 in/outgoing analog lines, one analog phone. Recently I was messing with the XTEN client, got to finagling with things, and not knowing what was wrong I upgraded from 1.0.7 to 1.0.9 (both asterisk + zaptel). I was testing various things, and found everything worked except outgoing calls. So I checked

Any body used patch, http://bugs.digium.com/bug_view_page.php?bug_id=0001719 to get the callerid for BT Line. I applied the patch successfully but could not get it to work. Any help. Here are the logs: -- Starting simple switch on 'Zap/1-1' Jun 17 18:22:31 NOTICE[426000]: chan_zap.c:4811 ss_thread: Got event 2 (Ring/Answered)... Jun 17 18:22:34 NOTICE[426000]: chan_zap.c:4811