similar to: Complete newbie seeks start . . .

----- Original Message ----- <snip> > I've downloaded the * software and the zaptel drivers. look in the zaptel source directory and you will see a file called README26 (i think, or something like that) i am not a linux expert but my linux 'experienced' partner told me something about the 2.6 kernel... > > And now, to be quite honest, I haven't got much of a clue

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

Hi I received the Asterisk Dev Kit Lite on Saturday and got a small PBX working fairly quickly using the config files supplied with the kit. This was on my desktop machine and the sound card stopped working. I turned the system off and moved the sound card to another slot to give it a different IRQ. On reboot, the modules zaptel, wcfxo, and wcusb all load OK and asterisk starts OK but there

My TE411p does not seem to like to have two PRIs from different telcos (span 1 and span 2). I can get one working, but not the other. However, if I use vpmsupport=0 when loading the wct4xxp module, they both work. But here is the problem, vpmsupport=0 disables the on board echo cancellation. Any ideas? BTW, here is zaptel.conf span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs bchan=1-23 dchan=24

Dear All The setup is te110p with an 8 channels PRI to make and receive all calls. SIP phones throughout the company. TDM400p with 4 FXS modules to send/receive faxes and make credit card transactions. I have an analogue phone on the tdm400p for testing. I can receive calls to the exten. There is a dialing tone. However, when I try to make a call I get a busy signal. Asterisk stated busy then

Hello, I would like to double check what Echo Cancellation my Digium Card uses. I thought I bought the little more expensive card that integrates EchoCancellation. How can I check? root at sn1:~# zaptel_hardware pci:0000:0b:08.0 wcte12xp+ d161:8000 Wildcard TE121 root at sn1:~# ztcfg -v Zaptel Version: SVN-branch-1.4-r4309 Echo Canceller: MG2 Is MG2 the correct one that I am supposed

hi i've been trying to get an old game (Dune 2) which i used to play through DOS to work on Linux systems, i've not used this before and am in need of an 'idiot's guide to Linux' i've gotten as far as having unpacked the file and installed it on terminal, it now to the point of running the Setup.exe however when i try to run the setup, i get the following command line

This is my first venture into VoIP from my Fedora Core 4 system. I came across a posting: http://atrpms.net/name/asterisk/ > > http://atrpms.net/name/asterisk-addons/ > > http://atrpms.net/name/asterisk-sounds/ > > http://atrpms.net/name/spandsp/ > > http://atrpms.net/name/libpri/ > > http://atrpms.net/name/zaptel/ on the Fedora

This was an interesting post from another list I'm on. I think that with all of the echo cancellation discussion happening, that someone perhaps might be on the lookout for this type of software, so this post was well-timed for Asterisk uses. It is perhaps the case that those of you working on volume/echo/etc stuff might find this useful towards your goals. JT >To: [snip]

I have an eight channel fxo setup (2 TDM400P cards) and I have them setup. Here are my configs: Zaptel.conf: fxsks=1-8 loadzone=us defaultzone=us Zapata.conf: [trunkgroups] [channels] musiconhold=default rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callerid=xxxxxx callwaiting=yes busydetect=no callprogress=no usecallingpres=yes callwaitingcallerid=yes

Anyone knows where can I find spandsp? Official site seems permanently down... TIA, Simone.

Is anyone using a cisco router as an ISDN gateway with Asterisk? As you might have seen from a couple of my threads, I have been looking at Fritz! and Cologne cards, both of which require development against a specific version of asterisk/zaptel (e.g. chan_capi), which is intrusdive and causes a lag in deployment. I was thinking a better approach might be to use a seperate gateway, such as a Cisco

Is there any more docs on this other then the blurb on beta.redhat.com? I got a spare non-critical victim err... test machine I want to try this on and have all the RPMS, but would really like to chew on a little more detail before I leap. Regards, Henri -- "People die." --The Cynic's Book of Wisdom

bRotheRs & sisteRs, I am once again attempting to learn enough Latex voodoo to get something done, and failing comically. The document "RJAuthorguide.pdf" mentions that one can get page width figures through the use of the "figure*" or "table* environments, but despite considerable searching through the mail archives and reading Frank Harrell's discussion of

I recently plugged in Phone to my TDM400P Card to test out something I mostly use sip phones to interface with *. All of sudden I'm getting lot of line static noise coming of the card is there any settings I should look at or anything I need to do on the command line at this point I'm open to any ideas I'm running 0.7.1 on Redhat 9.0 machine. Any insight would be greatly appreciated.

I'm looking to add a single FXO port to my Asterisk box. It looks like my options are a Digium Wildcard X100P off eBay for $6.99, or a Wildcard TDM400P with an FXO Module from Digium for $125. Can anyone explain the tradeoffs (other than the ability to put 4 FXO/FSO modules on the TDM400P). What about RTC for the system - I know the TDM400P provides it. Does the X100P? Thanks!

<p>I am new to the group but have searched the doc's FAQ's etc before posting here.</p><p>&nbsp;We are attempting tie our asterisk server/service to the building's PBX, the building is in the UK and the local PBX is a meridian option 11 installed and mainteined by BT.</p><p>BT Have installed a NTBK50AA E1-PRI card in the meridian with daughter cards

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

Has anyone had success with the TDM400 in production? I have multiple boxes where these cards lock up and the only thing that will fix them is to unload *, modprobe -r wctdm, modprobe wctdm, load asterisk. Does not matter if it is a FXS/FXO module. I know this topic has been discussed many times before, but my questions is not "is anyone else having this problem" since I know that

My daughter has a BT account, with a BT supplied single-port router. I'd like to replace it with a standard router, but the settings appear to be totally hidden. If anyone reading uses BT, could you please tell me where to find the info? Maybe off-list, to save bandwidth for others/ Thanks Anne