similar to: aacraid monitoring tool?

Anyone managed to get this working on CentOS 4? I'd love to hear how. .dn

I have successfully kickstarted 3.4 x86_64, but after updating my repo to 3.5 I see a kernel panic when it loads vmlinuz. Funny thing is that I had one box that would kernel panic while trying to install centos-3.4-x86_64, which then would install fine after updating to 3.5, but now my other mahcines will not kickstart. --

One of my systems have two onboard NICs which uses the e100 and e1000 drivers (yes, the interfaces are not the same). This system kickstart fine with CentOS 3.x. I recently tried to rekick it with CentOS 4.x but was unsuccessful in doing so. When kicking CentOS 4.1, the interfaces are swapped around, i.e. eth0 becomes eth1 and eth1 becomes eth0 (as described at

I'm spec-ing a development server for some Haskell hackers. In particular, they need to be able to build and run the Glasgow Haskell Compiler (ghc), the x86_64 port of which isn't quite there yet. My current thought is to get an Opteron-based system, but load it (initially, at least) with the 32-bit i386 version of CentOS. That buys me near-term ghc compatibility. In the future,

Does Centos include any runtime monitor/control software for raid arrays on AACRAID devices as on IBM 3650's? -- Les Mikesell lesmikesell at gmail.com

Hello, I''m using Xen 4.0.0 compiled from source with the 2.6.31.13 kernel that it pulls down on its own. I added support for the aacraid driver to the kernel using ''make menuconfig'' from the build-linux-2.6-pvops_x86_64 subdirectory, and then built and installed the whole thing using ''make install'' from the xen-4.0.0 directory. I compiled this

This isn't exactly a Centos question but maybe someone here can help: Does the AACRAID controller (as in an IBM 3550) store its config info on the drives or internally? I only have one of the boxes and want to load Centos 3.x on several drives which can be swapped into servers at another location. With SCSI, all that took was a full disk dd copy and a little fiddling with the HWADDR for the

I have just built a new SunFire X4100 server with an Adaptec 2230SLP RAID card using FreeBSD 6.2-PRE kernel (from September 20). Everything is working extremely well except I cannot run the aaccli utility on this controller. When I try to open the controller, it gives this error: Command Error: <The current AFAAPI.DLL is too old to work with the current controller software.> On

Hi, I want to ask you, if you release an RPM package for samba 2.2.2 for Redhat 6.2 too, and not only for version 7.1 Thanks a lot Tomas Zeman

Hi, Upon upgrading xen-kernel I see the following error/warnings at the end , though the upgrade process went fine. Installing : kernel-xen 1/1 /etc/sysconfig/kernel: line 7: alias: scsi_hostadapter0: not found /etc/sysconfig/kernel: line 7: alias: aacraid: not found Detailed logs : #################################################### --> Running transaction check

Hi there, I'm currently trying to install a server with Centos 4.3 x86_64. I have issues installing drivers from a Driver disk, I got a driver(2810SA) from the Adaptec site, I started it up with "linux dd" It reads the disk fine .... I can see the aacraid module in the list but as soon as I choose it. Then I get a screen saying "Do you wish to load more Driver Disks?" I

This isn't really a Centos question but it affects the systems so I'll ask here anyway. I've noticed when swapping disks around on IBM 3550 boxes that some of them see one more cylinder on drives than others but I can't find any settings or differences that might control this. It's an obvious problem when you fdisk/format on the one that sees the additional cylinder,

I've just had an strange thing with Adapted 2200 RAID controller (with optional battery module installed). Basically, new card, worked perfectly for weeks, several reboots and stuff. Then all the sudden, when I rebooted machine this today, system would simply freeze during boot. BIOS showed the card initialized properly, kernel module was loaded (from initrd) and it found all of the arrays,

Hallo, has anyone a hint how to use an Adaptec RAID 51645 under Centos 7? A volume is created using the controller interface but isn't active under centos. Thanks for hintsts Ralf

Does Centos/RHEL 4.4 supports the CERC 6-Channel SATA RAID Controller that comes with the Dell PowerEdge 830 Tower Server? -- ------------------------------------------------------------ Erick Perez Panama Sistemas Integradores de Telefonia IP y Soluciones Para Centros de Datos Panama, Republica de Panama Cel Panama. +(507) 6694-4780 ------------------------------------------------------------

Hello, does anyone run xen on an dell poweredge 750 ? I am getting the following scsi errors on the raid driver on hight I/O load. aacraid: Host adapter reset request. SCSI hang ? aacraid: SCSI bus appears hung with kernel 2.6.8 the whole maschine hang on this error. now I am using xen 2.0.6 with kernel 2.6.11.10 and the latest aacraid driver from adaptect. so the device only hang ca 1:30

Greetings, I just got new Dell PowerEdge SC1420 and a 6 channel SATA RAID controller card (Adaptec 2610SA from Dell also) When I attempt to install CentOS 4.2, it doesnt find the RAID 1 mirror I set up. (2 X 160Gig drives) It doesnt find any hard drives at all. Does anyone have anything to suggest here? Thanks Ryan

Folks, Mercurial is selectable as an installation in OpenSUSE 10.3 YAST. I have done the following: hg clone http://xenbits.xensource.com/xen-unstable.hg hg clone http://xenbits.xensource.com/linux-2.6.18-xen.hg make dist sh ./install.sh I tried running the following to create the initrd but it failed: Depending on your config, you may need to use ''mkinitrd'' to

Hi all I?ve got a few Intel Z87 chipset machines with Adaptec 5405 raid cards (latest firmware), they work fine on 3.18 but during Dom0 boot using kernel 4.9.13 it hangs at ?Using clocksource tsc? and the aacraid driver keeps trying to reset Has anyone seen anything like this? I?ve tried specifying clocksource=xen in grub instead of the default of tsc, and that has the same issue. HPET is

> Like I just mentioned in a different thread, I need to use > the ''noapic'' > options on both the PowerEdge models I''ve tried.. I''ll try to > build up a Xen vs. non-Xen kernel tomorrow or Tuesday and > grab a diff for you. Which PE models are they? We have quite a few different Dell PowerEdge models running 24x7 in the test lab, and