Displaying 20 results from an estimated 2000 matches similar to: "Segmentation Fault TDM22B & TDM04B"
2005 Aug 16
0
What should my next steps in troubleshooting this TDM04B error be?
Hello
I have installed a TDM04B and disabled any devices not required in my PC.
(TDM04B is analog card with 4 ports to plug into telephone co lines). I am
running this version of *
Asterisk CVS-HEAD-01/10/05-02:11:15-AstLinux built by root@ls on a i686
running Linux
As you see below the wctdm module is loaded:
pbx root # lsmod
Module Size Used by
binfmt_misc 12296 1 - Live
2005 May 24
0
Problems installing TDM22B
Hi list,
I am trying to install a TDM22B in my * box. I am using a Pentium III with
SuSE 9.2 (2.6.8-24-default) and * 1.0.7. I installed the TDM22B (no IRQ
conflicts), recompiled zaptel, libpri and asterisk. I modified a file (can?t
remember which one) to create my devices entrien in /dev/. I also tryied
?make config? but modules don?t load at startup.
But this is not my problem; I
2005 Jun 20
1
Unable to reconfigure channel
Hi all,
I have a problem with the cvs head zaptel library: I cannot update my
zapata.conf into asterisk when I issue the reload command from the CLI
prompt; only when I stop and restart the asterisk service.
The system sends the following message:
Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap:
Ignoring switchtype
Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364
2004 Nov 26
0
TDM22B - how to setup the extensions ??
I got this nice TDM22B with two green modules left and two modules right
/var/log/messages shows:
Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196
Nov 27 00:37:53 dns kernel: Freshmaker version: 71
Nov 27 00:37:56 dns kernel: Freshmaker passed register test
Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO
Nov 27 00:37:56 dns kernel: Module 1: Installed
2004 Nov 29
2
Problems starting Asterisk with TDM22B
Im getting the following error when I try to start Asterisk
WARNING[16384]: chan_zap.c:765 zt_open: Unable to specify channel 1: No
such device or address
Nov 29 21:40:43 ERROR[16384]: chan_zap.c:6195 mkintf: Unable to open
channel 1: No such device or address
I'm using a TDM22B card.
=============
# Zaptel Configuration File
#
loadzone=us
defaultzone=us
fxoks=1-2
fxsks=3-4
==============
2005 Jul 12
3
Help Configuring TDM04B
Hi:
I had an fxo card from Digitnetworks and it was
working fine on my Asterisk box. I then replaced it
with TDM04B. I changed the zaptel and zapata to
include the four channels. When I run ztcfg, I get
configuration errors:
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04:
2005 May 30
2
Error in Zapata Config?
When I reload the config, I see this error in the CLI. However, I don't see
what I have done wrong:
== Parsing '/etc/asterisk/zapata.conf': Found
May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring
signalling
-- Reconfigured channel 1, FXO Kewlstart signalling
May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring
signalling
-- Reconfigured
2004 Dec 23
1
ignoring signalling
I reloaded my asterisk and found some red lines flushing by. When I
stopped it I see:
WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling
WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge
WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining
Reconfigure channel 1, FXO Kewlstart signalling
Reconfigure channel 2, FXO Kewlstart signalling
2006 May 09
0
problem with hang up with TDM31B
Hy,
I'm working with asterisk 1.2.4 and zaptel 1.2.4
With these version an the options in zapata.conf:
answeronpolarityswitch=yes
hanguponpolarityswitch=yes
I don't detect polarityswitch. When asterisk reloads I see in CLI:
May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring
answeronpolarityswitch
May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring
2004 Dec 10
2
Asterisk 1.0.3 - Signaling on E100P.
Hello list ,
I?m putting to work a new asterisk box.
I?m running * 1.0.3 with (one )
Wildcard TDM ( 2FXS* 2FXO) and
(one) E-100P.
Both boards are working well. ztcfg
don?t show me any error.
zttool list both cards as "OK"
But when i run asterisk on verbose mode
i get those errors :
[chan_zap.so] => (Zapata Telephony)
== Parsing '/etc/asterisk/zapata.conf': Found
--
2004 May 19
4
TDM400P problems with 1 FXS, 1 FXO
Hi-
I'm totally stumped configuring my TDM400P with one FXS and one FXO
module. Before I got the FXO module, I used to have an X101P, and
everything was working very well. Now * doesn't seem to recognize the
FXO channel. I've searched the wiki and the list archives. Stock Debian
3.0 stable installation. Any advice? Thanks.
-- David
Here's my configuration:
modprobe zaptel
2005 Mar 11
1
QuadBRI ,TDM400 and SuSE9.2 (Sencond try)
Hi all, this time with the complete configuration files...
We need help with our SuSe9.2 asterisk box
We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone.
We have downloaded the bristuff (0.2.0-RC7j) and installed it without
problems.
once we downloaded and compiled asterisk, zaptel and all other stuff,
the module installation succed in this order:
modprobe zaptel
modprobe qozap
2005 Mar 10
2
QuadBRI ,TDM400 and SuSE9.2
Hi all,
We need help with our SuSe9.2 asterisk box
We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone.
We have downloaded the bristuff (0.2.0-RC7j) and installed it without
problems.
once we downloaded and compiled asterisk, zaptel and all other stuff,
the module installation succed in this order:
modprobe zaptel
modprobe qozap
modprobe wcfsx
then the ztcfg output this:
Zaptel
2006 Feb 19
3
Asterisk start errors with TDM2413E
I get the following errors when starting Asterisk.
== Parsing '/etc/asterisk/zapata.conf': Found
Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to
specify channel 1: No such device
Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open
channel 1: No such device
here = 0, tmp->channel = 1, channel = 1
Feb 19 21:14:35
2004 Aug 08
0
Zaptel.conf and Zapata.conf for TDM12B
Can someone please help me with my config settings for my TDM12B. I have got
the FXS port to work fine, but I cannot get asterisk to startup with any
settings for the fxo ports.
It appears to be something related to the message "Signalling requested is
FXS Kewlstart but line is in FXO Kewlstart signalling". However, I have
tried what appears to be every possible configuration option. I
2006 Feb 17
0
I must be missing something zimple...
I'm configuring a box with a TDM400P with 2 FXS and 2 FXO. I configured
the FXO's first to try them, and they worked (I could talk to myself
thru the PSTN. But when I add the FXS's to zapata.conf and restart *, I
have a problem...
[chan_zap.so] => (Zapata Telephony w/PRI)
== Parsing '/etc/asterisk/zapata.conf': Found
-- Registered channel 4, FXS Kewlstart
2006 Feb 21
0
asterisk 1.2.4 doesn't detect the PSTN hang up
Hy,
I'm writing from Spain.
I have the 1.2.4 asterisk version and 1.2.3 zaptel version. I've heart
that this asterisk's version detects correctly de hang up of PSTN, but
in my case this thing doesn't happen.
Moreover, my asterisk sends the next messages in the CLI:
Feb 21 15:03:13 WARNING[10363]: chan_zap.c:10876 setup_zap: Ignoring
signalling
Feb 21 15:03:13 WARNING[10363]:
2004 Nov 24
1
I just got my TDM22B - but no data sheet
I just got my TDM22B, but the package did not include anything else,
like datasheet.
1. Where can I download it?
2. Which outlets are FXS/FXO ??? (depending on the green /red card
positions)
3. Does it need the extra power??
bye
Ronald
2007 May 18
1
CallerID not detected by TDM22B
Hi,
I am using asterisk 1.4 with Digium TDM22B card. My system is running well
except CALLERID. I have tried all options for cidsignalling, cidstart but no
luck.
Btw, I am living in Malaysia. From google web site, I found some one having
the same problem with new version of asterisk but not in old versions.
I do not want to try the old versions of asterisk. I really appreciate if
someone can
2008 Jan 21
1
FXS damaged at TDM22B
Hi All;
If one of my FXS port damaged at TDM22B because we
connected the Telephone Line cable to the FXS port
while it should be connected to the FXO port, then can
I order S110M FXS Module and fix it instead of the
damaged FXS? (This if we assume my problem that really
the FXS port damaged).
Rregards
Bilal