similar to: SS7 E1 cards

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

Hi, I've posted this question on OpenSS7 mailing list but I didn't get a clear answer. I have a system running asterisk using Digium T400P card. Can this same card be used with OpenSS7 project to carry SS7 links? Is there any difference between these two cards? -- Matteo D'Amato Network/Telecom Administrator Intelco Communication Inc

Hi, there are still some questions to be answered by OpenSS7.com in order to decide, whether E400P-SS7 is a good choice for the asterisk SS7 support. In the meanwhile I'm also in negotiations with another manufacturer (whose name I currently may not tell due to a NDA) of SS7 hardware, who gets likely persuaded to offer a cheap SS7-PCI-card which would be suitable for asterisk. Asterisk users

Hi, one month ago, I announced, that I will look at the openss7 project in order to use it together with asterisk. It took a while for me to check the capabilities of and around the project. Since the openss7 project consists of only one person, and when there was just silence for a long time in the project's mailing list, I doubted, whether it was a good idea to consider using openss7. In

Hi, Does Asterisk support SS7? Google shows an old new post from Feb. 2002 stating that OpenSS7 would help add SS7 support to Asterisk, but presently OpenSS7 seems to be dead and I can't seem to find anything about it at Asterisk or Digium's sites. What happened? -- Regards, Tais M. Hansen ComX

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hello.. I have a customer who wants to connect 2 PBX's over IP.. The setup should look like this: [PBX] <-- SS7 --> [Asterisk] <-- IAX --> [Asterisk] <-- SS7 --> [PBX] Since there are no SS7 cards , I was thinking at a way of carrying the E1 data as bulk...Can I do that ? How ? Is possible a scenario like this ? I'm thinking of IAX because I don't

Hi all, Does somebody know what's new with SS7 and * ? I'm very interested. Is it ready ? I'm prepared to pay if necessary. Thanks, Angel.

Hello. I am new to this forum. If this issue has been discussed already, please inform me, but my STFW have indicated that it has not. If SS7 were available on * would it make commercial sense to use it? There are case studies on the web (courtesy of the Death Star :->) for ISPs with 10,000+ subscriber lines showing clear cost savings in transitioning from PRI to SS7 controlled IMT. My

In reference to an old post from 2002: http://www.marko.net/asterisk/archives/0203/0103.html How does one go about doing this? Also, what is the present status of the OpenSS7 stack in Asterisk? What can it do now? And is there any possibility in the future of developing a DS3 card for it, if only for the purpose of mostly DACSing? Which is still a level of intelligent call control on the

Has anyone tried to get dialogic ss7 trunking to work with Asterisk? I did some googling but nothing helpful turned up... Could a person get an intel dialogic and get * to see it like a zap channel? And use it for incoming and outgoing trunk access? -- respectfully, Joseph ------=============

Does anyone know of a device that will take an SS7 link and convert it to a PRI? -- respectfully, Joseph - (606) 477-2355 x140 ------=============

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Hi, We are currently testing Asterisk with Wildcard 100XP and serveral Cisco ATA Box. Everything works great except that the card does not detect the hangup signal. We are using a standard Belgian PSTN line. I have not found anything about a be zone (only us, fr, de, nl, ...). Does someone experience the same problem? Do I need to create a new zone be (and how to do that)? Another small

Hello, Again one more question about hardware. What could you suggest me to buy. I need hardware to connect let's say 4 analog lines. (FXO). This hardware should "talk" to Asterisk of course.. Thanks very much for some advices :) Bartek -------------- next part -------------- An HTML attachment was scrubbed... URL:

<P>hi everyone,</P> <P>I know this issue has been raised many times before, i think still the problem remains. When a call is made through a Zap channel, whether it is actually made or not (irrespective of whether, engaged, busy, or actually answered), asterisk logs it in CDRs as a call made. This makes it impossible to do an accurate billing. Has anybody found a way to overcome

I thought everyone should know this. Jorge, After reading your page in the http://voip-info.org/tiki-index.php?page=Asterisk+SS7 please advise Your U.S. customers that SS7 is not done the same way as in the rest of the world and the requirements are different. The U.S carrier's require 2 redundant links. I know this first hand because we run an SS7 network. CARDOSO Jorge Miguel wrote: