similar to: Asterisk newbie questions

Hi List, I have a 2Mbps SDSL link which gets saturated during peak time because about I have about 3 E1 worth of g729 traffic going thru. So I'm planning to use IAX2 trunking to reduce bandwith requirement and squeeze out each and every bit of this (expensive) bandwith. I've set up two boxes (debian etch), one in a remote data center (which has plenty of bandwith) and one behing

Can anyone point me to a reference or sample config for bypassing a nailed up (point to point) t1 between two PBXs with asterisk and a pair of t1 cards? Right now I have 2 Nortel norstars connected to each other via a leased line t1. I also have a solid 10mbps low latency microwave link between the 2 sites. My goal is to run an asterisk box at each end with a t1 card and Ethernet card to

Hello all, I`ve got an AVM c2 card instaled on my SuSE box. I?m having problems configuring its channels. I don?t know how to set up asterisk to use the CAPI channels. I don?t know how to call them. My capi.conf is as follow, [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] ;#########config de la primera interface CAPI##########333

Hi List, Is there a way to tell asterisk to only accept SIP streams from the same IP address that is used for signaling? Thanks, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi List, Yesterday night after a power off due to a faulty UPS my asterisk doesn't want to start anymore. Here is what I get on the CLI: Asterisk Ready. *CLI> Disconnected from Asterisk server: Bad file descriptor. Executing last minute cleanups == Destroying musiconhold processes Asterisk uncleanly ending (0). I use 1.2.7 I think on a debian sarge and cdr_pgsql too. Any ideas?

Hello, Could anybody tell me if there is a Linux distribution (or Kernel version) that works better with Asterisk. I am newbie and I don't know if there is a preferred Linux/kernel version for Asterisk. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040904/8798ff25/attachment.htm

Hi List, I was wondering if anybody had tried running Asterisk inside virtualization software such as Xen. Are there known problems doing it? Cheers, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hello, I use asterisk to to IAX2 trunking between London POP & Reunion Island pop. I would like to know if it's possible to do a kind of call-limit (i.e. restrict to XX) channels but on a per dialcode and / or destination basis. For example: [trunk] ; reunion proper, i want to send no more than 24 channels exten => _0262XXXXXX,1,Dial(IAX2/mytrunk/${EXTEN}) ; reunion mobile, i want

Hello all, Just a question, on asterisk box : I looking on the web , for asterisk at large , and 'asterisk future of telephonie' ... If we would like to change our OLD PABX 600 phone with 4 E1, to install a asterisk with full ip phone in SIP, Could we use 1 Box for asterisk with voicemail, zap channels and some agi script ? thanks Fabrice

Hi List, I'm using VoIPJet and NuFone as a fallback, and it seems that both of them are circuit busy! Also it seems that VoIPJet takes forever to return 'circuit busy' while NuFone does it instantly. At any rate, is there like a reliable third VoIP provider I can use for fallback when the two others are busy? Cheers, Jean-Michel.

Would anyone care to offer opinions as to the FXO interface which sucks the least :) I have an application in which it appears I must route certain calls out an analog PSTN line. Presently, I am testing an SPA-3000, but I can't seem to get the echo heard on the IP end of the call down to a non-annoying level. Any suggestions welcomed :) -Dorn

Hey guys. If my Asterisk box connects to the PSTN using SIP and IP over ethernet and doesn't require any authentication, what sort of a trunk would need to be created? Thanks, -- Nick e: nick.hoffman@altcall.com p: +61 7 5591 3588 f: +61 7 5591 6588 If you receive this email by mistake, please notify us and do not make any use of the email. We do not waive any privilege, confidentiality

Hi List, Being very new to Xen I have a few generic questions for the list, I hope to grab some useful advice and pointers to documentation. I am evaluating Xen to consolidate a few existing servers into one appliance (mainly in order to reduce power consumption, heat, and hardware failure risks). I plan to have a SER router, an Asterisk LCR router, a voicemail server, a calling card server

RAD appear to have bucketloads of products which bridge between various interfaces (E1, BRI, POTS) and their own TDMoIP protocol. The attractive thing about them for me is their availability in Australia. The voip wiki says not much about it (http://www.voip-info.org/wiki/view/TDMoIP), and certainly nothing about if there is any way to get Asterisk to talk TDMoIP. Despite the name, TDMoIP

Hi. I'm getting new lines for using with Asterisk. In my Telco they said I could choose between Analogic lines and RDSI lines... I've already bought a TDM400P with FXO modules. Can you give some hints on the differences between RDSI and normal Analogic lines? Would I have problems for using a RDSI line with the TDM? Any other issue in general? Thanks in advance, RODOLFO --- avast!

Hi, I need to have some SIP extentions on remote places where the latency from my asterisk box with public ip is 1~1.5 seconds. What codec will work fine on this sceneary? I'm planning to use iLBC, is a good choice? Regards, Guillermo.

Hi List, I was wondering if there was any device I could use to connect * to GSM networks. I don't need much capacity, maybe 2-4 GSM channels. As usual, cheap is better :-) Any tips on this? Cheers, Jean-Michel.

Hi, understand that the bandwidth utilized for each call is dependent on the codec used, wonder if Asterisk can monitor the total bandwidth utilized and restrict/reject new calls when the resource is insufficient to support them reliably? Regards Andy Tan -- Andy Tan andytan@fastmail.fm -- http://www.fastmail.fm - Does exactly what it says on the tin

Hi List, Do you know if there are any plans to improve i18n for Asterisk? The current i18n way of doing it with asterisk is very limited and most of the time does not work. For example, take voicemail: "message" "received" "at" "seven" "30" "am" might sound good in English. But: "message" "recu" "a"

Hi List, I've got * randomly hanging up on inbound or outbound calls on zap channels. I use a Digitnetworks X100P clone card. Any idea of what might be happening? Cheers, Jean-Michel.