similar to: Bristuff wackyness - not answering

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Hello everyone, I try to connect the Asterisk PBX Server on my NTBA (NT1) - actually its "hard"-connected on the box, but I've tried a crosslink-ISDN cable, too. My ISDN-Phone is connected on one port (of two) S0-Ports on NTBA. When I start Asterisk and want to make a call I'll geht a lot of this messages --> 040827-034639 WARNING[213005]: chan_zap.c:6902 zt_pri_error:

Hi- I've posted this on the bugs list, but I'd also like to see if others have had similar problems when connecting via E1 trunks (E400P). I'm getting numerous errors like the following during inbound calls to my E1 channels. These occur when the system is under medium load: WARNING[196621]: File chan_zap.c, Line 5404 (zt_pri_error): PRI: !! Got reject for frame 78, retransmitting

Hi! I have the chance to play with a couple of E400P cards, each installed in a IBM e330 XSeries servers (2 x 1GHz P-III CPU 2 Gb RAM, 36Gb SCSI HDD with RH8.0 2.4.18-smp kernel), and I'm trying to test/benchmark this e330/E400P combo generating calls thru /var/spool/asterisk/outgoing One e400P if doing the carrier work making calls and the other just receives the calls: Server#1

Dear List i have upgrade my * box with the latest CVS version of Asterisk Stable 1.0 and zaptel/libpri my system is MDK9.2 with 1 TE410P and seems work well for now but i have a little amount of traffic (25 IN/OUT calls) i only notice this Warning.. What kind of error is? ------------------------------- Apr 20 21:28:49 WARNING[147466]: chan_zap.c:5979 zt_pri_error: PRI: !! Got reject for

bri-stuff.0.1.0-RC4a on debian sid with 2.6.7 kernel isdn sk: Bus 0, device 18, function 0: Network controller: Digi International Datafire Micro V (Europe) (rev 2). IRQ 17. Master Capable. Latency=16. Max Lat=16. I/O at 0xe400 [0xe407]. Non-prefetchable 32 bit memory at 0xd8021000 [0xd80210ff]. i still receive error messages continuosly (every few seconds) i

Configuration: Linux wpbx 2.4.9-13 #1 Tue Oct 30 20:11:04 EST 2001 i686 unknown P4 2.5 GHz, 1 GB RAM T400P with 3 T1s plugged in. A flow of 46 calls (spread out over 3 T1s). Each call gets transferred (Dial) to the SIP platform and stays for 5 min. Case 1. Asterisk built out of CVS Mar. 19. Test was running for 3 days. Segmentation fault. Case 2. Asterisk built out of CVS Apr. 1. Test was running

Hi all- HELP! This is actually a revisit of a problem that I had earlier with E400P's at a customer site. Customer still gets locked up channel problem, but has learned to live with it (channels clear themselves after several minutes). The symptoms, which I believe are directly related: I'm having problems with tons of framing and "read" errors on my E1 connections (and

Hi I am using CVS-HEAD-05/09/05 and astcc. The call sometimes does not hang up at all, does not even get the warning notices, as it should, since the L option specifies that the caller gets played a message like 1 minute before the call is disconnected, and then the call should end. Its basically not working, although I seem to think that if only one call is being processed it does work,

I have a "Cologne Chip Designs GmbH ISDN network controller" in my asterisk box, and an ISDN line connected up to it. I downloaded the bri-stuff 0.1.0-RC4a package from junghanns.net and used that to compile asterisk using these instructions: http://www.voip-info.org/tiki-index.php?page=Asterisk%20zaphfc%20install When I try to call my asterisk box, my sip phone rings twice and then the

Hi I was doing some bandwidth testing, and my incomming usage is 36% more than my outgoing bandwidth. The setup is IAX2 trunking using GSM codec. Is there any obvious reason I am overlooking to figure out why there is such a big difference between the two.? I am using CVS-head September 3rd, maybe there is a version skew? Any suggestions will be appreciated. Thanks Clive

Hi ! I'm trying to configurate my first asterisk system. My test plant has an E100P Card and a 4 FXS TDM 400P card. I've an E1 configured for 15 channels. Telco says that crc4 is configurated so my zaptel.conf is: loadzone = it defaultzone=it span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 unused=17-31 fxoks=32-35 zttool shows no alarms. I've also tried changing the timing

In my efforts to solve a mystery of asterisk slowly loosing it's ability to take incoming and outgoing calls I set asterisk to restart b-channels every 60 seconds hoping I would find something odd after some time. So now I am looking at the CLI a few hours later and look what happens when asterisk restarts the 23 b-channels I have. pbx1*CLI> -- B-channel 0/19 successfully restarted on

I applied the florz patch but my problems remain. Now I get all sorts of weird errors on the console and I cannot make outgoing calls. Incoming calls work as expected. I am using a single HFC-S card with BRI. Any clue what these errors below are? Ri = 44651 TEI msg = 3 TEI = 7f Ri = 3800 TEI msg = 3 TEI = 7f Ri = 42399 TEI msg = 3 TEI = 7f Ri = 42409 TEI msg = 3 TEI = 7f Ri = 22078 TEI msg = 3

I'm running bristuff-0.3.0-PRE-1q The line seems to work but I get these messages on the screen every few minutes : 1 received TEI check request for TEI = 81 Jun 20 20:18:05 WARNING[27571]: chan_zap.c:8503 zt_pri_error: 1 TEI remove TEI = 127 Jun 20 20:18:05 WARNING[27571]: chan_zap.c:8503 zt_pri_error: 1 TEI remove TEI = 127 Any ideas ? Guess this is not normal behaviour? I'm using

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

Hi all, Sorry to bother you with the potentially not too bright question, but since I cannot get it to work, I'll have to ask someone.. I've got this vector: > token [1] sal skal skal bak b_r d_ gal kal l_r n_r pak p_r [13] sal sl_r sn_r spak sp_r st_r s_ bak d_ gal l_r pak [25] p_r sak sl_r sp_r t_ kal n_r s_ st_r sak kal

I've this error How i can find the problem? Apr 23 12:24:43 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:47 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:48 WARNING[131081]: PRI: !! Got a UA, but i'm in state 1 Apr 23 12:24:53 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:25:02 WARNING[131081]: PRI: