similar to: Polycom IP 300 - Displaying Only Caller NAME... What about NUMBER?

I'll do that, but I'm sure that it's the Polycom :) Caller ID shows up fine on my 7960... W/ the name on top and the number below that. -- Executing NoOp("SIP/614-3ede", "Caller*ID is Matthew Marlowe <6092521155>") in new stack When the phone rings, only 'Matthew Marlowe' would display. When I answer, both the Name & Number will show.

When I dial a SIP phone which is specified in the sip.conf, but the phone is not connected, Asterisk gives the message "The user at Extension XXX is on the phone ...." Shouldn't the message be the unavailable message? Is there something wrong with my set up or is this a "bug" with Asterisk? Simon Brown

Greetings, This is probably some configuration issue, but for some reason my system has stopped playing a ringing sound when an extension is dialed. The phone rings but there is no ring sound in the ear piece. Gene Kochanowsky

Has anyone been able to get the minibrowser on the Polycom SoundPoint IP 500/600 phones working? If so could you share the relevant sections of your config with me?

Does anyone know of a device that will take an SS7 link and convert it to a PRI? -- respectfully, Joseph - (606) 477-2355 x140 ------=============

Hi Everyone! I live in Sweden and can not get CallerID to work on analog incoming lines. I m trying to find out if DTMF style CallerID works on a FXO card (X100). I`v seen one solution with a modem attached in parallel with the X100 just to provide the ID on its serial port. It must be much better if this can be implemented in to the X100 driver. Any info about this would be highly appreciated.

I think I have it configured properly. ztcfg -vv shows it as channel 1 and zttool shows it as OK. But I can't dial out. When I try, it shows it arrive in teh right stack, but then issues the following errors: channel.c:1676 ast_request: No channel type registered for '{PSTN-1}' app_dial.c:554 dial_exec: Unable to create channel of type '{PSTN-1}' = = Everyone is busy at

Assume you have the messages button on your Cisco phone set to dial 3009. Here's an sample dialplan entry that will make the "DND" and "ToVM" and "Messages" button work as expected. This should work for both -stable and -head. exten => 3009,1,GoToIf($[X${RDNIS} != X]3009,4) exten => 3009,2,VoicemailMain() exten => 3009,3,Hangup exten =>

I saw several threads requesting an Asterisk forum to complement the email list. i.e. http://lists.digium.com/pipermail/asterisk-dev/2004-February/003103.html I recently created an Asterisk forum within TMC's popular VoIP forums for everyone to use. http://voip-forum.tmcnet.com/voip-forum/forum/forum_topics.asp?FID=15

i have been trying to get a newly liberated (from vonage) cisco ata-186 (sip ios v3.1) working properly with asterisk. my client is behind a linksys wrt-54g, which up to this point hasn't proven to be a problem (i have several sipura spa-2000's and polycom phones working just fine behind them). (i'm running cvs-head from yesterday). after looking at the various suggestions,

I've managed to use GhoustScript (gs) to take a postscript file and convert it to tiffg3, but I CANNOT seem to make it merge multiple files. Here is the output from tiffinfo on the file that SG generates: fteTYGeh2v.tif: TIFF Directory at offset 0x8 Subfile Type: multi-page document (2 = 0x2) Image Width: 1728 Image Length: 1056 Resolution: 204, 96 pixels/inch Bits/Sample: 1

I just got a Polycom soundpoint and I set it up using the phone and web based admin. I cant seem to figure out the config files and they are confusing me greatly and I dont have time for it :) Some things are odd, like on every reboot it seems the volume I set is reset? is there any way to fix that. And the ringer seems low. - Even all the way up Anyone willing to point out a good asterisk

I'm getting the following when sending to a specific fax machine. Any ideas? File name is '/var/spool/asterisk/email2fax/7F2SOeYJiU.tif' Changed from phase 0 to 2 Slow carrier up Slow carrier down Slow carrier up <<< NSF: 20 00 00 11 80 00 8a 49 10 53 54 49 52 4c 49 4e 47 20 43 4f 56 49 4e 47 54 00 67 00 80 80 80 0c 01 02 NSF without final frame tag The remote is made by

Hi, We have to servers set up in two different networks. We are able to connect calls via IAX and they work perfectly. We do not see caller ID from clients on either side. Our Grandstream phones say Eri and our XTen phones say Asterisk. We did a debug and I am pasting the output from both servers below. We tried setCallerId in several different ways. We see the value get passed to the

Using the following defnitions with a C7960: exten => 3001,1,Dial(SIP/3001,15,r) exten => 3001,2,Voicemail2(u3001) exten => 3001,102,Voicemail2(b3001) exten => 3001,103,Hangup If someone is on this phone (real conversation) and another call comes in, the second call goes through the 15 second timeout and is dropped into the 2-priority as "unavailable" (not the 102 busy as

It appears Asterisk can handle DTMF inband on only a limited selection of formats, of which G.729 is not one. The issue appears to be something involving "short data" -- whatever that is. (I'm inferring all this from looking at dsp.c in the vicinity of the error message I was getting, which pointed to line 1424.) What *is* "short data"? Is this really a show-stopper for

Hi all, I'm writing my graduation theses : analysis VO-IP protocols , and I cannot find any documents about Cisko Skinny Client Control Protocol. I have Cisco CallManager and some IP-phone and I'm sniffing traffic between that, but I don't understand, how this protocol works. Clearly i'm looking for description of SCCP commands and explanation some basic SCCP scenarios or what

Hi there, I just tried today's CVS: 4/23/2004 version and found a strange loise with music on hold. Basically, when on hold you hear very distorted music as if it was very loud. This is the exact same problem described last year at: http://lists.digium.com/pipermail/asterisk-users/2003-April/009735.html http://lists.digium.com/pipermail/asterisk-users/2003-May/011688.html No answers on

Hey everyone, I want to run different lines directly to different extensions on two FXO analog interfaces. ie; Zap/1 goes to Ext. 101, Zap/2 goes to extensions 102 Does anyone know of a way to do this? Thanks! Chris

Hi, Has anyone got the X100P to work with an anlogue line in the Republic of Ireland? I have the X100P installed but zttool indicates a Red Alarm status on the card. It is on its own interrupt and I have tried different PCI slots but all to no avail. Are there any alternatives to the X100P that can work with asterisk and are likely to work in Ireland? Thanks, Aaron