similar to: zaptel configuration

Hi, in response to a previous posting regarding getting the x100p to work, I was told to run "zap show channels," but when i do i get "no such command 'zap'" There was a previous posting on this, but the guy never posted the solution. thanks, Imran

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

Hi, Sorry, in my last mail I wrote "wcfxs" instead of what I actually used, "wcfxo." I just got two digium x100p clones and installed asterisk on fedora core 2 which took some tweaking. After getting asterisk up I installed the zaptel stuff - then modprobed zaptel, wcfxo, which worked fine. ztcfg is showing two channels configured, but when I start asterisk and

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp kernel. I've two x100p cards connected, only one card is reconigzed by asterisk. 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) 02:03.0 Communication controller: Tiger Jet

Hi, I installed a 1-port FXO on my Ubuntu 8.4. I was earlier only hearing a fast clicking sound and now I am not hearing any dial-tone. The FXO card has 2 slots: [phone | line ]. I hve connected the wall-phone-input to the "line" slot and "phone" to my home-phone. I do not hear any dial-tone on my home-phone. Asterisk seems to recognize my hardware....here are the relevant

I've had a few problems with my system holding the line after a call has been made, just now I rebooted and noticed the following in /var/log/messages Aug 13 17:23:15 Sheriff kernel: wcfxo: DAA mode is 'FCC' in the file wcfxo.c the following structure is initialised as below which would suggest that FCC is wrong for France or pretty well all of Europe. static struct fxo_mode {

Hi, I'm using zaptel-1.2.22.1 with asterisk-1.2.10 and following steps to make zaptel working... OS is gentoo linux 2006.1 Hardware: --------- 0000:05:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 22 I/O ports at b400 Memory at ff900000

Hi all, After reading great things about the OSLEC Echo Canceller (http://www.rowetel.com/ucasterisk/oslec) and seeing the reactions of people who have tried it on a recent Trixbox thread (http://www.trixbox.org/forums/trixbox-forums/open-discussion/need-people-echo-problems), it sounds like it is the "bees knees" for sorting out echo problems with cards like the x100p. Has anyone

Hi All, I have followed below steps to enable echo cancellation. # cd /usr/src # wget http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.28.tar.bz2 # tar xjf linux-2.6.28.tar.bz2 # tar zxvf dahdi-linux-2.1.0.4.tar.gz # ln -s /usr/src/dahdi-linux-2.1.0.4 /usr/src/dahdi # mkdir /usr/src/dahdi/drivers/staging # cp -fR /usr/src/linux-2.6.28/drivers/staging/echo /usr/src/dahdi/drivers/staging # sed -i

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

Hi I'm a little lost on how to set things up with the two FXO cards I have: I want card #2 to dial a number when a call comes in on card #1. Using the following configuration, card #1 picks up the line and remains silent, instead of dialing out through card #2. Anybody knows what's wrong? --------- /etc/zaptel.conf --------- # Zaptel Configuration File # fxsks=1,2 loadzone=fr

Hello, I have few questions about Asterisk. I installed Asterisk from CVS on FreeBSD and I made cvsup 2 days ago. 1.I couldn't find Asterisk version using "asterisk -V" command. How can I to find version information? 2.I am using Wildcard X101P (FXO) and Wildcard TDM400P REV E/F (FXS)on it. I tried Asterisk CallerID feature, but unable to get it. I tried callerid signaling V23,

Hi, I just got two digium x100p clones and installed asterisk on fedora core 2 which took some tweaking. After getting asterisk up I installed the zaptel stuff - then modprobed zaptel, wcfxs (for the fxo cards), which worked fine. ztcfg is showing two channels configured, but when I start asterisk and do show channels, i see no active channels. zapata.conf has: signalling = fxs_ks

I just installed two new X100P's today in my RH7.3 box and was poking around /proc What does the RED refer to on board 2? /proc/zaptel/1 Span 1: WCFXO/0 "Wildcard X101P Board 1" 1 WCFXO/0/0 /proc/zaptel/2 Span 2: WCFXO/1 "Wildcard X101P Board 2" RED 2 WCFXO/1/0 Any clues on how to setup channels on the two interfaces?? I am up to here in

I have just got my X100p card and am trying to install it. I have built and installed the zaptel drivers without any apparent errors and I am now trying to get them working. I have the following in config files In /etc/zaptel.conf fxsks=1 In /etc/asterisk/zapata.conf signalling=fxs_ks context=default channel => 1 Now when I try ti modprobe the drivers this is what happens: Command:

Owias, The 537 is, for the most part, a drop-in replacement for the Digium card. Please search the archive and the Wiki, as there have recently been several discussions about this exact subject. To my knowledge that is about the only modem that works, but keep in mind it is _not_ supported. That being said, follow the instructions on Digium's site for installing the X100P and you should be

I have read thru what other users have tried in this list when they have experienced seemingly similar issues to what I have, without success. I suspect there might be an issue regarding both the X100P and TDM04b cards being used in an Intel SE7525GP2 motherboard, as I had to even wait for a BIOS update from Intel in order to utilize my 3ware 9500 SATA raid controller on it (3ware Kb -->

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Hi All, I hope I'm posting this to the appriopriate list, and that cross posting to two lists is OK. (If not, I'm sure I'll hear about it quickly :)) I'm running Asterisk on my (new) VIA EPIA-V motherboard. This seems to be the ideal platform for a home version of asterisk - its small, quiet, low power, and should have plenty of computing horsepower if only it would work!

Hi, I' ve just connected a carte X100M to my asterisk server running zaptel-1.2.5, libpri-1.2.2 and asterisk-1.2.6 on SUSE 10.0. When I make modprobe wcfxo and modprobe zaptel I haven't any error, I have also chan_zap.so module existing in /usr/lib/asterisk/modules. But, when i run ztcfg, it shows me this: Zaptel Configuration ====================== Channel map: 0 channels configured.