similar to: Servers

Im looking for an Intercom solution thats interoperable wit Asterisk. Ive read several posts about people using the 2nd lines on some SIP phones w/speaker phone. Unfortunatley I dont that is going to cut it in a large warehouse enviroment. Does anyone have a solution that uses a "loudspeaker" ? Thank you, Steve Maroney

Hey guys, Im about to sign up for VoicePulse Connect. Of course, I plan on using my asterisk server to "register =>" with the service. I would rather sign up with VoicePulse via SIP instead of VoicePulse Connect. My asterisk box is behind another Linux box serving as my nat/firewall. Does anybody think I will have a problem ? Should I stick to IAX and VoicePulse Connect or can I use

Anyone know who that good looking female is thats on the Digium.com website ? Ok, my Real question is I noticed that Digium has relesed a new T1 card with an echo canceller. I also noticed that its supports E&M Circuits. Im I have very little knowledge on T1 circuits and traditional PBX's so what Im asking is can I use Digiums T1 card to connect to another PBX via a tie line ? Or does

Im trying to get IAX to work between my * and FWD. I activated my iax2 account on iax.fwdnet.net and I get the output: "Registered to '65.39.205.121', who sees us as 68.14.203.254:4569" when I start asterisk. I tried used the Call Me tool on fwdnet.net but I dont get any calls even though the Call Me tool says everything looks ok. Can someone call my FWD number and just leave

Hey guys, How much disk space is used by Asterisk to store voice mail for about 10 - 20 users/mailboxes Thank you, Steve Maroney

I easily get confused when try to undertstand FXO & FXS ports. Is it possible to use an ATA to connect to a TDM400 card. If so, would I use FXO modules or FXS modules ? My goal is to connect my asterisk server to Vonage (via the ATA they send me) so I can use thier standard plan and do with out the Softphone account feature that only allows a few hundred minutes talk time. Thank you, Steve

I'm in the process of turning up a PRI in one of my markets and have run into a problem I have never seen before. I am unable to place a local outgoing call. Long Distance over the same PRI works fine. When I attempt to place a local call using the PRI I see Asterisk attempt to dial, and am greeted with a busy signal. This signal appears to originate on the telco's switch. I have had

Just curious if any of the Asterisk installers are doing anything special to protect themselves from a possible lawsuit caused by 911 failure during a Asterisk/computer crash? I realize that any traditional PBX or even a phone line can fail but, anything running on a computer is probably going to be less reliable than most PBXs. Anybody requiring customers to acknowledge and sign any kind of

I have: RedHat 9.0 TDM40B asterisk-0.9.0 compiled from sources zaptel-0.9.1 likewise /etc/zaptel.conf contains fxoks=1-4 loadzone = us defaultzone=us loaded modules zaptel and wcfxs /etc/askterisk/zapata.conf contains [channels] language = en signalling = fxo_ks context = phones channel => 1-4 /etc/askterisk/extensions.conf contains [general]

Does anyone know if the HandyTone 486 has the option to turn the two ethernet ports into either a switch/hub, or does it have to do NAT ? Thank you, Steve Maroney

Hey guys, I was wondering what POE solutions are being used ? Ive done some searching on google and found that PowerDsine seems to be good brand. Any comments,suggestions, and experiences on POE hubs other POE products would be greatly appreciated. Thank you, Steve Maroney

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a

I have the original version of the IAXY. I had it laying around collecting dust, now Im actually putting it to use. When I call my voicemail extension (8500), Before I get the voice prompts from the voicemail app, I hear tones that sound like the caller id tones that are heard when montoring a phone call. While watching my Asterisk CLI, I see this error at the sound of each tone: Jul 21 23:06:03

say I needed to send a broadcast message that I wanted every user to hear when the pick up thier phone? can I "Play,message" on a line just before they get dialtone? or maybe after they dial before ring? how about a "ringdown" to a voicemail box and on end return them to thier line for the dialout? can * do ringdowns? when a user picks up an extension it automagically

Hey all, Does anyone know what this means? I was running asterisk fine. Installed it on a new pc and I am using the g729b. codec that is optional. I ran the install for the codec it went ok but when I run askterisk via asterisk -vvvgc it gives me this error anyone know? I make sure I entered in the correct reg number. I followed the steps correctly. Too Registration error! Please try

Dear, I have two Asterisk PBXs with an E1 interface/RJ-45 port in both boxes. I need to connect both PBXs with E1/R2 and UTP cable. What are the requirements to deploy the UTP cable ??? Straight-through or crossover ??? What are the pinouts in both peers ??? Thanks a lot, Alejandro

All, I have AAH 1.0 installed using Digium TDM04B and Grandstream GXP2000 phones. All seems well other than the phones have to be reset up to 5 times per day. It is like they lose thier ip connection or maybe thier SIP connection. Has anyone else experienced this issue? I have the phones set for static IP addresses and that doesnt seem to help either. Any help would be greatly

Hello. I am going through the documentation and trying to find if asterisk can help me in my case. It is quite difficult to find answer because I do not know the exact question. I have two location. Each in different country. Both locations have Siemens HiPath - different type and software. I can not use card that would allow me to connect those PBXs using SIP. But I have some free ISDN and

Hi, I'm buying an interface for my Toshiba DKT424 to connect to *. Initially it is a trial to route internal calls over our wan. Think of it as a tie trunk between 2 pbxs. I expect to get PRI from the telco our layout will be like this: telco_T1_PRI to * to various PBX or TDM or IAX to * to other pbxs My question is, is there benefits to connecting with PRI over a standard T1 within my

Hi, I have been reading the mailing list archives and google results but havent been able to find quite the information i am looking for. Perhaps someone on the list can give me a hand. Our company has several sites. Two of which we regularly make calls between over the PSTN. Both sites currently have thier own PBX systems but they are not linked by any means other than the PSTN (and we pay by