similar to: Broadvoice problem

Hi All First time poster, long time reader. I just ran into something really bizarre. I've enabled videosupport and have been testing sip calls with Xten Eyebeam software, it works (mostly) However, when I have Videosupport=yes In the [general] section of my sip.conf, broadvoice calls fail w/ "We're sorry your call cannot be completed at this time" So... I've

Hello, Have a weird problem when using asterisk (1.0.6). There are certain numbers I cannot dial when using asterisk with my broadvoice account. No problems with inbound. With outbound calls, I can call some numbers (for example broadvoice customer support number) and unsuccessfully with some. However, when I configure my account directly on x-lite, I dont see these outbound problems. Here is a

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

All, I signed up for a broadvoice BYOD plan over the weekend (very excited about their offering) and after about an hour I had asterisk registered and was making in and out bound calls. However, the next day (without changing anything) I couldn't call in or out and haven't been able to get it going again. I can connect using a softphone (X-Lite) and make calls in and out

Ok we have found a better solution. Put everthing back the way it was and make sure that you have this line in your general section of you sip.conf file: srvlookup=yes We have added a SRV entry in the correct place now. So everyrthing should go the correct servers. -james --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.726 /

you can not ping that address because ICMP is turned off. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com]On Behalf Of Deon Rodden Sent: Monday, July 26, 2004 2:22 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Broadvoice problems again Attn: James Greetings, C:\>ping 147.135.8.129 Pinging

I've tried everything with the * box after this weekend. I have read every document on the problems people are having with them after this weekend as well, but none of them address my problem. I checked my settings in my sips which I have below as well, I have changed the host file a few times, but this was new to me and I never had modified it before. I have and the same results

Hi, I can't make outgoing calls via Broadvoice. I have tried each and every configuration that was posted to list previously. I am able to receive incoming calls fine. I get the following in asterisk console: ===================================================== asterisk*CLI> show version Asterisk CVS-HEAD-03/10/05-22:51:28 built by vicky@asterisk on a i686 running Linux

I finally got my incoming and outgoing to work on Broadvoice with a configuration file that is no where close to the one given by them. Here it Is (sip.conf). For others who have a working config could u please share so that I could compare. Thank You [broadvoice] type=friend username=[number] fromuser=[number] secret=[password] host=sip.broadvoice.com fromdomain=sip.broadvoice.com

Connecting to proxy.dca.broadvoice.com Calls all of a sudden cannot be completed. Cannot ping proxy.dca.broadvoice.com Changed to proxy.chi.broadvoice.com pingable, but now get the following: Got SIP response 500 "Internal Server Error" back from 147.135.12.128internal error Called Tech Support... get dead air then carrier busy signal. Anyone else having

Is the Broadvoice service up? I just signed up with them and started receiving calls in no time but could not make calls. And after a few minutes I cannot even place calls. register => [number]:[password]@sip.broadvoice.com [broadvoice] type=peer fromuser=[number] host=proxy.lax.broadvoice.com fromdomain=sip.broadvoice.com context=from-broadvoice dtmfmode=inband any help would be

Hello guys. I am a fairly new user to Asterisk, and I'm just having a tough time. My goal is to set up a VOIP PBX. I have signed up with a BroadVoice number, and I have three systems with SIP phones. The PBX and the SIP phones are all behind a Cisco PIX running NAT. I am using Asterisk CVS version from yesterday. I also tried 1.0.3 with little luck. The SIP phones are two X-Lites on

Today, We have added INVITE Authentication. This seems to bring a large amount of problems to people in the way since they can't make outbound calls. Here's what needs to be done. You need to add three variables to your peers or friends, username, authuser, and secret. username=<phonenumber> authuser=<phonenumber> secret=<registration password> Dan

I have an idea, tell me if this wouldn't work... I know it's really ugly, but it might help some people until we can get round robin DNS checks for peers... Since * does not do GetHostByName() again until you reload your config, and BroadVoice and I'm sure other sip providers are using round robin DNS, why not create 2 [<your server here>-out] contexts in sip.conf, and then in

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

I had my asterisk configuration working very well with broadvoice, but it stopped working this afternoon. I plugged the Cisco 7960 phone I used for my origional signup (just a few days before they offered generic BYOD) and it works fine. I did notice it seems to do all of its comunication through proxy.broadvoice.com (I used tcpdump). I have never contacted broadvoice about using asterisk

Suddenly my broadvoice will no longer register. It was working fine for over 1 month without a single problem, now I get a SIP registration timed out message. I called them, and I was told that they are experiencing problems, and they hoped to have it resolved ASAP. I called them at around 10 AM EST this morning. It's now 8:30 EST PM, and I still have not heard back, and the problem is not

if you have anyone questions about your service you can contact us at the support 978-418-7300 James Jones Broadvoice Technical Support ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Ben Wern Sent: Sat 8/28/2004 4:34 PM To: Asterisk Users Subject: [Asterisk-Users] Broadvoice BYOD Plans - 3-way and Call Waiting Can anyone who is using Asterisk

HELP! Ok, so I have the following SIP.CONF: [general] context=default port=5060 bindaddr=10.1.1.200 externip = XX.XXX.XX.XX localnet=10.0.0.0/255.0.0.0 disallow=all allow=ulaw allow=g729 allow=g726 allow=alaw register => ##########@sip.broadvoice.com:XXXXXXXXX:##########@sip.broadvoice.com/1234 [sip.broadvoice.com] type=peer host=sip.broadvoice.com fromdomain=sip.broadvoice.com

Hello! I have asterisk updated from CVS on 31/8/2004 with sample configuration. I have just changed the sip.conf to register asterisk with sip proxy in out intranet. Then I can successfully make call to asterisk and go to demo IVR, but no response to dtmfs. I try to make call from several sip phones: Cisco7960, Ata186, Snom200. All of them send telephone-event in INVITE, but asterisk answers