similar to: FXO probs in Aus. Should I give up?

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

Em (20:59:21), Asterisk Users Mailing List - Non-Commercial Discussion escreveu: >On Tue, Jun 21, 2005 at 08:09:52PM -0300, Alessandro wrote: >> >> Does Somebody know why no load modules to FXS? I used zaptel-1.0.7 >> version. > >What color are the modules? >Post your /etc/zaptel.conf > >-- >Mike Mike, The color is green, red ans bluw. Link

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

zaptel compiles fine (make linux26) but when I modprobe ztdummy I get the follow error. [root@localhost zaptel]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy System info: Linux localhost.localdomain 2.6.9-5.0.5.ELsmp #1 SMP Thu May 19 19:24:44

I bought an Aastra PT480 from digium, but I wanted to see if I could get some more help with this before Monday. Any help would be appreciated. I have the phone connected to the TDM400P card, and I also have the T100P and the X100P in the same box. My problem is, it appears as if the phone and asterisk can't understand each other. The port the phone is connected to always remains

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

I have a normal backup phone (and an alarm panel) sharing the POTS line with the Digium X101P FXO: | | Wall |>---+------X101P FXO as Zap/5 | | | Phone & Alarm Whenever the Phone is used, Asterisk sees a 'false ring' signal immediately when the phone is hung up. The Alarm panel dials out nightly at around 1AM, and each time it completes the call, Asterisk

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support

Hi everyone (Mark, Jim). I am new to the list but thanks to both Mark and Jim, I have being using "asterisk" since summer 2001. I am just updating my version that was a year old. Yes, I know, I got busy with other things like paying bills so I don't have to sleep with the dog anymore. Anyway, one of the frustrations I have been dealing with (keep in mind that my version of

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hi there! I'm setting up a connection between Asterisk ver. 1.2.13 and a Harris 20-20 PBX. More less everything went fine, but the problem I have now is when dialing to the Harris PBX, it seems to pick up my call as soon as it reaches it. For example if from the Asterisk outgoing folder I dial an extension, say 100, and play a prompt as soon as it is picked up, the promt is beign played as

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

Wow ! No reply... May be I must talk about X100P instead of X101P ? Is someone has yet encountered this kind of "no sound" problem when bridging two FXO lines like this (first as input, second as output) ? Any idea ? TIA. Best Regards, Francois BERGERET, France. ----- Original Message ----- From: "Francois BERGERET" <f6hqz-m@hamwlan.net> To: "Asterisk Users