similar to: zaptel installation

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a

Hi, in response to a previous posting regarding getting the x100p to work, I was told to run "zap show channels," but when i do i get "no such command 'zap'" There was a previous posting on this, but the guy never posted the solution. thanks, Imran

Hi, Sorry, in my last mail I wrote "wcfxs" instead of what I actually used, "wcfxo." I just got two digium x100p clones and installed asterisk on fedora core 2 which took some tweaking. After getting asterisk up I installed the zaptel stuff - then modprobed zaptel, wcfxo, which worked fine. ztcfg is showing two channels configured, but when I start asterisk and

Hi, I am new to asterisk. I have downloaded Asterisk and Zaptel from the cvs root. I am installing them on Mepis with linux-2.6.7 Whenever I try to do "make" in the zaptel directory, I get the following errors. make -C /lib/modules/`uname -r` /build SUBDIRS=/usr/src/zaptel modules make[1]: Entering directory `/usr/src/linux-2.6.7` make[1]: *** No rule to make target

Hi, I just got two digium x100p clones and installed asterisk on fedora core 2 which took some tweaking. After getting asterisk up I installed the zaptel stuff - then modprobed zaptel, wcfxs (for the fxo cards), which worked fine. ztcfg is showing two channels configured, but when I start asterisk and do show channels, i see no active channels. zapata.conf has: signalling = fxs_ks

Hi, I've purchased two x100p clones, and when I try accessing a line from asterisk with something like this: exten => _1NXXNXXXXXX,1,Dial(Zap/2/{$EXTEN}) (is that only supposed to put you on channel 2 or actually dial the # for you?) but I first hear noise, then a dial tone, but as soon as I start dialing numbers I get feedback and noise, and the call doesn't go through. Any

Hi, I was wondering if anyone knows where i can find out the standards used by telco's in different countries... and how to configure asterisk to support them. Secondly, whenever i try Dialing a zap channel, all i get is no sound on the phone source, and noise on the destination line. thanks Imran

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk

Hi Since Im using the mISDN drivers and no zaptel stuff, I had to install ztdummy to get MeetMe to work. Well, that was the plan. Now, after getting the latest zaptel version over CVS (Im using Kernel 2.6), uncommenting all the modules except ztdummy in zaptel.sysconfig file and compiling this by "make", "make install" and "make linux26", I rebooted and

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hi, I'm trying to dial out on a vonage line connected to a zap channel using stuff like: exten => 200,1,Dial(Zap/2/${EXTEN}) but it doesn't work - when i dial in the extension, i can see on a phone connected to the same line that it's gone active - but there's no dialtone. also tried adding a wait period before accessing the line and exten =>

Hi, I've got a data set with a control group and a number of experimental groups, that have unequal sample sizes, and am measuring the number of people in each that respond yes or no. I'd like to use a dunnett test in R, where the syntax is supposed to be like: library(multcomp) test.dunnett=glht(anova_results,linfct=mcp(method="Dunnett")) confint(test.dunnett)

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

Hi all, I have a problem starting the ztdummy. Here is what happens: [root@asterisk /]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy After this, ztdummy is visible with lsmod, but when I try MeetMe, I get following: == Parsing

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

Hi, I just setup two voicemail boxes - but after they record the wav file, they don't seem to email it even though i have the correct format in my voicemail.conf file. Aterisk doesn't give me any feedback besides the recording of the voip file... and then stays there. Secondly, I can't get the Playback() function to work. Thanks, Imran

Followed the "instructions" on voip-info.org regardinging fedora FC2, making Zaptel seems to work fine, however when I modprobe I get this. It looks like a version mismatch somehow. Ideas? If this ooc, sorry first post here :-) modprobe tor2 WARNING: Error inserting zaptel (/lib/modules/2.6.5-1.358smp/misc/zaptel.ko): Invalid module format WARNING: Error inserting zaptel

Using the latest SVN of zaptel and asterisk, I can no longer receive incoming analog calls. The caller just hears it ringing but Asterisk doesn't pick up. I am seeing these error messages: [Apr 9 09:38:02] WARNING[16564]: chan_zap.c:6470 ss_thread: CallerID returned with error on channel 'Zap/2-1' [Apr 9 09:38:50] WARNING[16570]: chan_zap.c:6470 ss_thread: CallerID

Hello. I am new to Asterisk but I have been reading like for a month all de documentation and tutorials that i have found. Most of them from de voip-info.org. Recently I set up an Asterisk server based on Debian 'Sarge' 3.1. Everthing was looking fine. I even locate an old modem that would work like a X100P Clone (an Ambient MD3200) and after compiling and installing zaptel it is

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down