similar to: skinny or sccp?

I could use some skinny/Cisco help here. Was finally able to get the phone registered to * but whenever someone tries to call that phone it freezes and reboots itself. Same thing happens when you pick the handset up off the 7960G; it locks and reboots about 5 sec later. Here is what * shows when I plug the phone in: -- Starting Skinny session from 64.72.107.1 Device SEP000F3442E4A7 is

Hello folks, I'm trying to install chan_sccp and get this error [chan_sccp.so]Oct 2 00:28:06 WARNING[-151090528]: loader.c:248 ast_load_resource: /usr/lib/asterisk/modules/chan_sccp.so: undefined symbol: __use_ast_pthread_create_instead__ Oct 2 00:28:06 WARNING[-151090528]: loader.c:429 load_modules: Loading module chan_sccp.so failed! After this, mpg123 goes crazy and shoots my

Hi list! I'm trying to configure the Kirk IP 600 wireless (DECT) system. The wireless phones are regular DECT phones, the Kirk IP 600 is doing the voip part by registering/gatewaying the phones to a callmanager server. The phones do not work and I think the problem is that they do not register at asterisk but I'm not sure because I don't understand a thing of the sccp/skinny

Greetings: I have a working configuration for SCCP on our LANS which doesn't route RTP correctly to a skinny phone behind NAT registering from a remote public IP. Configuration: asterisk 1.4.35 servicing only skinny phones trunked to asterisk 1.2.40 which services chan_phone FXS, zap FXO and SIP phones; both instances of asterisk are behind NAT and run on the same host (using different base

Hi All, I'm thinking of creating a new asterisk server using the latest 1.4 stable release to replace my ageing Asterisk SVN-branch-1.2-r7231 (its been a while!). My only concern - my phones are Cisco 7960's (with sccp firmware 7.2 loaded) and to support them better, I remember compiling in a skinny(?) driver to replace the (from what I could tell) basic in built sccp support. After

Evnin' (o; As chan_sccp is pretty much dead, doesn't compile on FBSD anyway and isn't supported on * 1.4.x I tried going with chan_skinny... The Cisco 7970 registers and is being acknowledged by * but that's it... I see no lines on the 7970 display configured and it is not reachable or it can't make any outboudn calls... The docs are pretty non-existent for skinny and the

Any one knows where to install chan_sccp for asterisk 1.4 ???????. Please guide me from where can I download the asterisk 1.4 sccp channel driver and how to install it because I tried to get chan_sccp-mayday05.tar.gz When I trying to install it ,error happened like this. Please help me how to solve this issue. [root@XPL t]# cd chan_sccp [root@XPL chan_sccp]# make clean rm -rf

When I try to compile the new chan-sccp-easter2005 with asterisk 1.0.6 I get the following error on make: Now compiling .... chan_sccp.c 744 lines chan_sccp.c:67: conflicting types for `sccp_request' chan_sccp.h:1723: previous declaration of `sccp_request' sccp_pbx.h:5: storage size of `sccp_tech' isn't known make: *** [.tmp/chan_sccp.o] Error 1 I tried looking in

Hi list! I'm using phones that emulate a Cisco 7940 with chan_sccp. When I was using Asterisk 1.0.5 (bristuffed) I never had any such message on the console. The phones do work. Is this a bug in chan_sccp or a feature of asterisk 1.0.6? Thx!

Hi, I tried to connect cisco 7910 into asterisk system using chan_sccp.so. But I got a major issue : - when I called from 7910 to another sip phone in the same asterisk server, the call took place normally. - when I called from 7910 to another sip phone in different asterisk server, the call is answered but I cannot hear nor say anything. The phone just immediately lose its tone. - when I got

Before I got down the path of converting a Cisco 7960 I have over to SIP I wanted to try and set it up using Skinny. The phone registers ok with Asterisk. When I call a SIP softphone extension on my network the call is made and I can answering it. However no voice is heard over the call. When I debug Skinny on the console after the call has connected I see the following messag: Recieved Alarm

I have some Cisco 7960's and want to use them with SCCP - I have gotten it working with a few different firmware versions but all seem a little flakey. I know that SCCP is not as solid as SIP but am wondering, which firmware version is advised for use with chan_sccp from http://chan-sccp.sourceforge.net/ -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All, have some decent success on the 7920 "activation" in Asterisk. Latest status: chan_skinny does NOT work with 7920 chan_sccp does WORK with 7920 (!!) however: to remove coredumping the chan_sccp just comment out the MWI (messagewaitingindicator), then it compiles fine. Then change sccp_helper.c: return "P0060302" instead of the old value. and voila: Phone is

I have a new asterisk installation (1.4.2) that is working fine with SIP. Now I'm trying to add 2 cisco ip phones (7960) running SCCP (latest chan_sccp). I have the phones booted, and the tftp directory all setup, etc. But the phones do not quite work right. When I lift the handset I only get a dial-tone 1 out of 5 or so times I try, though hitting the speaker button works. I can dial

Hi, I have bought two Cisco 7960 phones. I have tried to set-up them to work with Asterisk over Skinny protocol, but when I try to dial the phone from Asterisk it says that all lines are busy. Is there something that should be configured on the phone's side? Can someone help me with that? Also, I would like to upgrade these phones to use SIP. How can I get the SIP firmware for my phones. I

hi! i had some good news regarding the cisco 7920 and the internetworking with asterisk (and possibly SIP ?). Status: chan_sccp.so not coredumping anymore :-) Phone contantly in reboot loop [see below] :-( Reboot Loop means: ------------------ Phone auth's with AP Phone gets IP from DHCP & TFTP Server Phone loads OS7920.TXT Phone loads SEP<macaddr>.CNF.XML Phone loads

Please forgive me my ignorance ... I've spent two days trying to find out something about the format of the default configuration file, which CCM produces. The only example I have so far is the one from the chan_sccp source. There were tons of references on entering the callmanager commands on a cisco command line - which I don't have (don't need thanks to chan_skinny + chan_sccp).

Hi All, Does anyone have any experience getting a 7936 to work with Asterisk? Do you need to use SCCP or is there a SIP image for the phone? I have a few 7960G's and they are working with SIP, just curious if the config of the conference phone is the same and if anybody has any good setup links. Thanks! NB -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi! I have two, not too related questions: - the probably simpler one: if anyone can help me out using a Cisco 7905G with chan_sccp? I did already managed to get it working with a SIP image, I'd just like to see it work with this one as well. It's probably something I screw up with the configuration, as the phone registers, only I don't get any lines with it, although I have it

Hello everyone! Anyone know if there is a way to use chan_skinny or chan_sccp to emulate a Cisco 7960 and talk to the CallManager. I realize it is intended to talk TO the phone, but I'm looking for an SCCP softphone solution (OS X). IPBlue has a client for Windows, yes. So, how much of a stretch can this be? Can't find any info on this anywhere. Tried Wiki, etc. Could someone please shed