similar to: budgetone 101 and buttons

Hi All I have 3 GrandStream BudgeTone-100's which connect to an * box with a HFC-S based ISDN card using ISDN4Linux. I have setup the BudgeTone-100's to use Early Dial which for calling between the three phones works well, but for the external calls using the following extension exten => _9.,1,Dial(Modem/g1:${EXTEN:1}) Only the first digit is dial on the ISDN Line. Does anyone know of

I'm using tftp server that automatically loads on each reboot, for some reason the last 2 files fail to load each time. (and I think this has always been the case) Aborted 192.168.16.32 C:\Program Files\TFTP Desktop\1.0.5.18\cfg000b82005c24 Octet, Send 192.168.16.20 25 Jan 18:25 Error Aborted 192.168.16.32 C:\Program Files\TFTP

I have found that the NTP server is not contacted when the phone (Budgetone 100) comes back from a power down. I must reboot the phone without powering down to get the phone to contact the NTP server for the time. It doesn't matter whether I reboot from the phone's web site or using the menu reset function: either works. I have only tested this with a private NTP server. This may

Everytime that I make a call to a Budgetone 101 phone. I always see the following: -- Executing Dial("SIP/1001-bac5", "SIP/1000|20|tT") in new stack -- Called 1000 -- Got SIP response 302 "Moved Temporarily" back from 172.22.5.4 -- SIP/1000-465e is busy I can use X-Lite all the time to make a call without a problem, but any of the budgetone 101 phones

Hi Folks, Since there isn't a grandstream forum AFAIK I guess someone here may be able to shed some light on this. Apologies if this is viewed as offtopic.. I think I may have killed the firmware on my Grandstream Budgetone 101. I found a source for the 1.0.5.30 firmware and made the files available over tftp. The phone downloaded the files but now doesn't boot and hangs with a blank

Is anyone using this combination successfully? I have a dell 500sc running rh9 and asterisk 1.0rc1. It is configured with an x100p. I have a Sipura SPA-2000, laptop with Xlite and a Grandstream Budgetone BT-101. I have signed up with Voipjet (they use iax2). I also have an FWD number via iax2. I can sucessfully call back and forth to all devices via zap, sip, and fwd. I can successfully

I am setting up a small Asterisk system for use at home. I have one Budgetone 101, one Cisco 7960 and two Xten lite softphones. So far everything is working expect for an issue with the Budgetone. When a call is placed between the Budgetone and any other phone, the call is setup and sounds good. If I hang-up on the Budgetone, everything is ok. If I hang up on the other phone, the Budgetone

I have the MusicOnHold feature working great when called from ATA-186 extensions. It's pretty cool. However, when I call from a BudgeTone-100 phone, no music is heard -- instead it continues the ringing feedback and acts like the call is unanswered. At the same time, I can call from (multiple) ATA-186 extensions and hear music as long as I like. How can I debug this? As far as I can tell,

Hello guys, I ask you to share your experience with your BudgeTone 100.... I have my asterisk @ work and I've bought a GrandStream BudgeTone (SIP phone) and I usually use X-Lite I have plugged my BudgeTone into my home network because I want to be called even at home. I succeed to register my X-Lite with Asterisk from home but I can't do that with my BudgeTone. (I don't know

I'm using 1 BudgeTone 100 IP Phone and a Sipura 2000 for all my old analog phones. The analog phones with the Sipura seem to work great. Voice quality is fine on both ends on the Sipura. I'm using the Teliax service and I use the Ulaw codec for all phones. However, I'm struggling with the BudgeTone 100. On my end, I find there is lot's of voice cut outs. I'm told my

Just for the record and to possibly help with others who get BudgeTone phones. My asterisk box is behind NAT, and I use Vonage, NuFone, and iconnecthere for my "POTS backhaul." On the front end I have an ATA186, a Digium TDM20, and now a BudgeTone 102. The BudgeTone definitely has issues wrt the RTP stream and NATting, although unfortunately I haven't yet been able to dig

I bought three plus two Grandstream BudgeTone 101 phones. The shipping cost more than the phone itself from Pulver store. The first shipping had one phone defect. Nothing on the display. (Can happen!) The second shipment had one phone with a defect display, but it still worked. The second phone's handset was defect too (microphone did not work). Changing the handset from this one to the

Hi, I'm considering giving the Grandstream BudgeTone-102 phones a try. I've been using Cisco 7960's to date, but the low cost of the Grandstream phones are hard to ignore. I have two questions: 1) Does the message waiting indicator on the BudgeTone's work with Asterisk? 2) The one line 12-digit LDC concerns me a bit. Is the LCD able to display both the CID number and name on

Hi there, I'm having problems with the Grandstream Budgetone 101 on hangup - "show channels"/"show channels concise" output is still showing the call's channels as active. The problem does not exist when I use SJPhone, so I'm assuming it isn't an Asterisk configuration issue. Has anyone seen this, or better, does anyone have a fix? :) Thanks, David. --

I have a problem with using voicemail on the Budgetone phones. When entering the mailbox and password, sometimes some keys will register multiple times (as shown on console when it says no such user in config file) and sometimes some keys won't even register at all. It seems totally random. Has anyone seen this problem? Any recommendations would be greatly appreciated. Thanks. Brian

Hello, I am trying latest stable Firmware for GS IP Phone BudgeTone 101 found at http://gs-firmware.gratissip.dk/firmwares/ and the phone doesn't send a register staement (nothing in thertereal log). With the 1.0.3.81 version, the phone register properly. Is ther any know bug with the SW Version? Best regards, Daniel ANDRE -- Daniel ANDRE (mailto:daniel.andre@iris-tech.fr) IRIS

I have a couple of Budgetones that I am playing with trying to get them to work with * from a remote network over the Internet (yes NAT joy!). My * server is in my DMZ and I have 5060 and my RTP range forwarded (UDP) to my public address (through a Cisco PIX). Internally, I can setup my budgetone, it registers and works great. I then have a Linksys router connected to another Internet

Hi, Just playing with a couple of Budgetone 102 phones and they are pretty good for the price. The only problem i'm having at the moment is when I get a voicemail on the Asterisk box the LCD flashes. Dialing *98 goes to the VoiceMail Manager, and asks for mailbox, I enter 201, then asks for password, enter my voicemail password set in the Extensions -> webadmin, then hit the

Hi Just recieved the above phone Does anyone have sip.conf and extension.conf example for the SIP phone working with the FXS w100p and the FXO tdm400d any help would be appreciated Thanks Robb

I noticed that the BudgeTone (I have the 102) with the latest firmware tries to download a file called cfg.txt (presumably the configuration) and a file called ring.bin (presumably a ringer) from the tftp server. The ring-in sound on the budgetone is the same as the ring-out sound and that is going to be confusing for users. I contacted GrandStream and was informed that both of these formats are