similar to: Inter-digit timers on t100

I am new to Asterisk. I am trying to ascertain the hardware setup (and associated cost) I would need. The documentation in the wiki (and elsewhere) is extensive but I am somewhat lost in product model numbers. Hence I need an initial recommandation to work on. 15 incoming lines, 25 employees). Initial scenario is to use * as a plain old PBX. I need voicemail, ability to transfer calls, ... I

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

I have two Adtran 750's connecting our analog phones to asterisk. On occasion, I get a channel that gets "stuck" off hook. 'show channels' shows: Zap/27-1 (longdistance s 1 ) Rsrvd (None) (None) And will just stay like that until the phone is manually picked up and hung up again (or asterisk is stopped/started). I guess this is a function of an unclean hangup (being

First time doing a t-1 config with *. running FC2 and CVS as of last W/E. i run modprobe wct1xxp and I get "Unable to open master device '/dev/zap/ctl' i look at /dev and there isn't even a zap directory. i was looking around and found something in /udev that looks promising but not sure what the deal is. ztcfg returns 24 channels configured but the same notice at the bottom

hi * users, anyone out there ever come across, worked with or heard anything about NEC's Univerge SV7000 Telephony Server? Link is at http://www.univerge.nec.com/products/list/sv7000/sv7000.html I'm just wondering whether it's as flexible, programmable and configurable as Asterisk. It also looks like they've got a whole range of IP phones

Hi, I'm seeing a problem when calling into my Asterisk server from a T100P with PRI signalling. I'm hoping someone has seen this as well, however, it's a little hard to explain. When I'm navigating through Asterisk on an inbound call from the PSTN, I'm getting a random 'noise' during the playback of sound files. The best way I can describe this noise, is imagining a

Hi List, a number of our customers are reporting dropped calls. here is the config. 1 T100P T1 Card 1 Asterisk (Mid Nov build) T1 is signalled as a PRI(National) The card will only sync up if we clock, if we line side clock the card goes into yellow alarm and won't sync up. the only errors we see are framing slips. Around 2500 slips over a 18 hour period. (this was reported from

I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and

Hello, I am not entirely sure the subject line captures what I am trying to do, but hopefully this description of the problem will help folks to see my challenge and hopefully offer constructive assistance. I have an experimental setup where I measure the decrease in oxygen in small vials as an organism, such as an oyster, consumes the oxygen. Each vial is calibrated before the experiment and

Hi All I am getting a strange prblem while installing TE420 on a Dell Poweredge T100 machine. I get a "TE4XXX: version Synchronisation error " nad the machine hangs which needs a hard reboot . Its a new machine and if i install TE410P then installation is successful. Strangely enough i have a working TE420F on another Dell POweredge T100 machine at a different locaiton ... The DELL tech

Just purchased a couple of T100 and E100 cards in order to interface from our company's proprietary system through a linux gateway. I am new to Asterisk and Digium. After installing the T100 card, I went looking for drivers for this card. Are the drivers built into the Asterisk application? If so, how do I enable the card through Asterisk? Are there any good getting started documents for a

....I THINK. When dialing 1+10 digits, I occasionally get a telco message "You must first dial a 1....". When I look at the console, the number is being sent to the ZAP channel properly. We're talking about a couple of POTS lines on a TDM400P. I'm thinking that it may be starting the dial too early after coming off-hook because I can just redial and have it work (or not)

I just added 2 Digium T100 cards. When my * box boots, it found them and configured them. When I enter genzaptelconf, it comes back with the following error: line 13: Unable to open master device '/dev/zap/ctl' Unloading zaptel hardware drivers: Removing zaptel module: rmmod: module zaptel is not loaded [FAILED] Loading zaptel

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

Hello All, Just looking some comments from gurus about this proprietary systems and phones: Inter-Tel Eclipse2 Model name: IP PhonePlus I did not find anything useful or reasonable about their products on their website or even in Internet.... except sales. -- Thanks and regards, Vasyl Rublyov

Help. Why is it that I can call out from my GSBudgetone SIP phone but the audio is "one-way'? Why is it that when I call my asterisk phone number, I get a fast busy?

I've been trying to figure out if it's possible to connect Asterisk to a parent Inter Tel Axxess system through the MGCP protocol. The archives for this list aren't searchable and I'm wondering if anyone has a simple answer... Dustin Moore

Hello all, I already successfully configured shadow copy service without a delimiter and regex. But as soon as I try to get this to work with regex, nothing shows up on the win client. My config looks like this: [global] shadow: localtime = yes shadow: sort = desc shadow: format = _%FT%T shadow: delimiter = _ shadow: snapprefix = ^\(monthly\)\{0,1\}\(weekly\)\{0,1\}\(daily\)\{0,1\}$

Hello - I'm using ATA-186 devices, with RFC2833 DTMF encoding. I am having problems with routines that input long strings of numbers, in that I am getting more than a small number of double digit entries. As an example, I have a section that asks for the user to enter a call forwarding number, and then puts that number into a database. Almost always, there are double digits when the

Is there any way to receive and send faxes using a T100 card? If so how is it done? Gene Kochanowsky Solution Sciences, Inc.