similar to: Euro isdn caller id problem

Hi, is anybody out there who can set the outgoing caller id on ISDN (CAPI or misdn) channels? I've tryed everything what I found in forums, os voip-info.com but no luck. I use a fritz card with CAPI in my first installation (1 BRI), and a hfc 4 port bri card with misdn on other. The first installation have p-t-mp configuration, the second one is p-t-p. Both configuration is EuroISDN in

Hi, I have a problem with setting outgoing caller id to "nothing" (secret) on our Wildcard TE405P connected to a swedish euroisdn line. Caller ID seems to work fine when connecting the same line to a Ericsson PBX - so something must be wrong in my settings, but I don't know what. I've tried: exten => _*70X.,1,Set(CALLERID(name)="") exten =>

Hi, I'm trying to set up an Asterisk pbx based on a Fedora Core 1 Linux box (customized kernel version 2.4.24). I want calls from my SIP soft-phones to simply be dumped onto the PSTN line via a BRI (EuroISDN). I have a cheap HFC-S based PCI ISDN card connected to the NT1+ interface, so I need zaphfc. I've read everything I've found at www.voip-info.org, then I've downloaded the

Hi Just received my spanky new TE405P today to replace my Cisco gateway... After much fiddling (I forgot to switch it to E1) I got it to work and everything "seems" to work perfectly on our ISDN PRI. If I dial-in from the PSTN to a SIP phone, the call goes through and if I hangup either the SIP phone or the remote end, the call gets disconnected and destroyed However, if I dial-in

Hi, I am using Asterisk with various brands and models of SIP phones. Especially the Welltech phones LP201 are particularly nasty with volume and echo. Even with the input gain (microphone) of the Welltech set to the max, the PSTN end can hardly hear the SIP user on incoming calls. Ztmonitor also only gives a level of around 3 === from the SIP phone. I have to increase the rxgain and txgain

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

I've googled / voip-info'd / searched until my eyes are blurry, but couldn't see the info I was looking for. I've turned here for help! Asterisk CVS head (9/7/04) Fedora Core 2 (updated to 2.6.6 kernel) DE405P (jumpers set to E1) I want to put asterisk in the middle of our current pbx (Meridian Option11) Currently the meridian has a 2MB pri EuroISDN card linked via a rj-45 into

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

Hi, I'd kindly ask for any advices, experiences and opinions on what Primary (and also several BRI) cards should be used on EuroISDN and Asterisk ? I'm also curious what features do these cards offer regarding echo cancellation (mostly when calling from analog lines) ? Thanks in advance, regards, Rob.

Greetings to one and all on this fine list; We have the current system: Meridian 1 Option 11 +-------------------+ | | ISDN/30 (DASS/2) ===> |NTAK79BB (2MB Pri) | | |<-->4x16 port Digital / 1x16 port Analogue ISDN/30 (EUROIDSN) ===> |NTBK50AA (2MB Pri)

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Hi To troubleshoot FreeBSD panics triggered by ISDN load on an asterisk system, we are looking to buy an ISDN call generator/simulator device. The minimum requirements include: - Not too expensive - PRI support (BRI support is a plus) - CCS+CRC4 farming + HDB3 coding - EuroISDN (DSS1) support. - A minimum of 4 ports (120 channels/concurrent calls) - Compatibility with Digium cards. - DUT in TE

Hi, I'm having some trouble setting up a Xorcom Bri 4 port. I have compiled asterisk and zaptel using the Bristuff bristuff-0.3.0-PRE-1y-g patches. So I'm running zaptel-1.2.17.1 and asterisk-1.2.18. The problem I'm having is that for one I get no LEDs showing if the unit is in TE and NT mode (not a issue for me but may have some impact on things) I have no errors in any logs I

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

hi, we are currently planning are large site which will migrate from an old siemens hicom pbx to asterisk. the customer is currently using a paging system (small receivers which display a callback number and a base station (transmitter) with several antennas at the site) the problem is, that the currently operative base station uses 4 ISDN BRI interfaces. But the protocol is old germany 1TR6

Hi Guys I have a 4 port PRI card that I need to setup each port in their own group. In chan_dahdi.conf I have the following which works for one port How do I add the rest of the ports in their own groups so that I can have different signaling on each? [channels] language=en switchtype=euroisdn pridialplan=unknown resetinterval=600 echocancel=yes echotraining=yes

Hi, I have Installed * on a DL380 with a Junghanns 4BRI card and 0.0.2 driver. I have 3 BRI lines connected to SPAN(TE) 1,2,3 and 2 Cisco 7960 with SIP image. I am connected to french PSTN (France Telecom) whith Euroisdn signaling. I manage to call SIP to SIP, PSTN to SIP but not SIP to PSTN. Any idea? Thanks Gwenn Gael Marronnier Here is what I get and my configuration...

Hello everyone. My land-line provider (Romtelecom) has a very nice offer for ISDN. All in all they offer me a digital land-line with 1 base number + 2 MSN's and that would make a grate addition to my full-time home office. Romtelecom say they're providing EURO-ISDN and the line is compatible with any euro-isdn compliant equipment. They say they'll install a NT at my office and this

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |