similar to: New office hardware set up question.

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks

I have an analog Fax machine which I wish to connect to the network and the Asterisk server. It will connect through a GS Handytone 286 converter and then into the LAN. Is there any information out there on what I need to write in *sip.conf* and/or *extensions.conf* to make sure the fax works as a fax? Channel 8 on my T1 is a reserved, dedicated line for the fax number. Do I need to

I remember a thread a while back asking about Linux distro's of choice. My flavor is Archlinux. But, I found a tiny discrepancy with Arch and Asterisk's install. Arch uses *mawk* for it's awk compiler, unfortunately...Asterisk doesn't seem to pick up on it. So, I installed *gawk* as well...and the install went smoothly after that. Just a heads up if you choose Archlinux

I don't know what I am missing in my conf files, but my T1 card grabs all available channels and won't let go of them? Anyone know what the problem is? -- Shawn Parker Network Administrator Cumulus Broadcasting, LLC. Columbia-Jefferson City, Missouri 1.573.449.4141 shawn.parker@cumulus.com

i know asterisk itself will install on a linux kernel 2.6.x, but i've seen places say that the zaptel drivers wont? is this still true? is it possible to build asterisk/zaptel on a linux 2.6.x kernel? -- Shawn Parker Network Administrator Cumulus Broadcasting, LLC. Columbia-Jefferson City, Missouri 1.573.449.4141 shawn.parker@cumulus.com

Shawn, That's a complete load of manure. I have an office full of 7960's, they work great with asterisk with the SIP images loaded. I'm about to pick up a lot of 7912's (simple one line phones, same as the 7905 but it has a built in switch). These phones have also been confirmed to work with Asterisk. I would recommend not going directly to cisco, and just find a reseller who

https://bugzilla.samba.org/show_bug.cgi?id=1791 Summary: using --delete with single directory mirroring doesn't delete files Product: rsync Version: 2.6.3 Platform: x86 OS/Version: Linux Status: NEW Severity: major Priority: P3 Component: core AssignedTo: wayned@samba.org

I have a test install set up as follows Grandstream 102 ---- Asterisk ---- X100P ---- Adtran Express 3000 --- ISDN line to PSTN Most things I want to do work fine except I do have some intermittent problems with an echo. I am assuming that this is created in the link between the X100P and the Adtran terminal adaptor. I am not sure of the proper terms but on the PSTN side of the Adtran there is

Nimbus is, among other things, a set of tools for making Xen available to remote users using popular protocols. Thanks, Tim Begin forwarded message: Date: Fri, 30 Jul 2010 17:08:26 -0500 From: Kate Keahey <keahey@mcs.anl.gov> Subject: Announcing Nimbus 2.5 final release We are happy to announce the Nimbus 2.5 release! This release introduces two major new features. The first one is

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

Rich Hi, After Qwest pronounced my circuits as within spec. (yes, disconnected from the house) I listened on the lines with my butt set. Clear of all noise and hum. I then got my box of Cat3 and laid a circuit around the outside of the house and into my lab. Still clear of all noise and hum. I then connected the circuit to the Adtran and made a call. Lots of hum and buzzz. As I said,

I've almost got this thing working. I have it set up on a centos machine to authenticate logins and automounts to windows file servers. But it won't allow me to specify a domain as part of the userid. I can set a default domain in smb.conf and logging into that domain works like a champ. And I can list the other domains with "wbinfo --online-status" (not sure what

Hello Can somebody send me please config files of zaptel.conf and zapata.conf for adtran fxs ports. I cannot make it work. I do not get a dial tone on Adtran and when I am trying to call from sip i get: app_dial.c:674 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy at this time There are no errors on T100P and adtran. Please help! B.

Here is some more stuff to add to the confusion about the "callprogress" option. I currently have my * system operating with a T100P talking to an ADTRAN TSU600 channel bank with 8 FXO ports connecting to the outside world and Grandstream SIP phones as handset extensions. At first I naively set "callprogress=yes" in zapata.conf. The results were typical of what many

We have been experiencing static noise on one of our phone lines connected to our Adtran Total Access 750 which is then connected to a T100P card. I was convinced that, after rain storms, the static would get worse, it was surely a problem of Verizon's. Verizon sent a field rep out today and he told our secretary (I was busy) that there was a hard ground on the Ring portion of the line.

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?

I thought this might interest a few asterisk users. I don't use them so I have no idea about Adtran's but I know a heap of people on this list swear by them. Cheers, Dean ________________________________ From: vclass.coordinator@adtran.com [mailto:vclass.coordinator_adtran.com@mail.vresp.com] Sent: Monday, 19 September 2005 9:59 AM Subject: ADTRAN Virtual Classes: Ensuring