similar to: BRI and E1 in same system

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

Hello I am using a Junghans quadBRI ISDN card and it is loaded and working. In Asterisk if I connect to ISDN line it is detected and tells me so. In my zapata.conf I have (abbreviated): [channels] switchtype=euroisdn signalling = bri_cpe context=default group=1 channel => 1-2 ;plus group 2 - 4 zaptel.conf: loadzone=uk defaultzone=uk # qozap span definitions # most of the values should

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hello, I cannot make any call with my new quadBRI card from Junghanns.net in my asterisk box. My asterisk box is built on Fedora Core 3 linux system. After compiling drivers from junghanns.net the card driver was loaded correctly with - modprobe zaptel - insmod qozap.ko ( as FC3 is running a 2.6 linux kernel) - ztcfg -vvv ( shows 12 channels correctly configured and the 4 leds on the card were

Hi, I'm trying to set up an Asterisk pbx based on a Fedora Core 1 Linux box (customized kernel version 2.4.24). I want calls from my SIP soft-phones to simply be dumped onto the PSTN line via a BRI (EuroISDN). I have a cheap HFC-S based PCI ISDN card connected to the NT1+ interface, so I need zaphfc. I've read everything I've found at www.voip-info.org, then I've downloaded the

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

Hi, I have installed a quadBri card, with Asterisk-1.0.10 and the bristuff-0.2.0-RC8s (* 1.0.10) When calling 0207654321 the following happens: -- Executing Goto("Zap/1-1 ", " salsa-helpdesk-day|s|1 ") in new stack -- Goto (salsa-helpdesk-day,s,1) -- Executing Dial ("Zap/1-1 ", "Zap/g1/0201234567|30 ") in new stack -- Requested transfer capability:

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hello Asterisk users. We have a quadBRI card installed and have the following problem. When starting Asterisk, the card is up and works perfect. But if no one uses it for 2-3 hours, the card seems to change status. If I try making a call from my sip phone to an extarnal telephone then asterisk registers that I'm trying to call, i.e. it's not a bridged but a show channels gives this

Hi, I have Installed * on a DL380 with a Junghanns 4BRI card and 0.0.2 driver. I have 3 BRI lines connected to SPAN(TE) 1,2,3 and 2 Cisco 7960 with SIP image. I am connected to french PSTN (France Telecom) whith Euroisdn signaling. I manage to call SIP to SIP, PSTN to SIP but not SIP to PSTN. Any idea? Thanks Gwenn Gael Marronnier Here is what I get and my configuration...

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz

Hello all Asterisk 1.2.10 BRIstuff PRE-1s Debian sarge I have an issue with my ISDN-BRI line. Asterisk tells me my D-Channel is down, no matter is I have an actual line plugged in or not. == Primary D-Channel on span 1 down I somehow got it to work once! The config tools do not indicate any errors whatsoever. Here is a rundown of various listings I can think about. (some things may show

Hi, (cc. asterisk-users, hope that is not a big Faux Pas) I've had trouble with the qozap driver for a LONG time now, where it will not recognise and ignore a missing ISDN2 line on a quad card if one of the 4 ports is unplugged or somehow faulty. The symptom is that is correctly recognises the fault, but then clears the RED ALARM almost immediately, leaving Asterisk thinking that it can call

Hi, Using Xorcom's bristuff-0.4.0-RC4-xr7.tar.gz (ie asterisk 1.4.25) with an old Junghanns OctoBRI (ie not the 2.0 version), zttool shows every port in TE mode, though half of them are in NT. Alarm column shows OK for every port, such as : OK octoBRI PCI ISDN Card 1 Span 1 [TE] Lay Globally, this system doesn't work (can't dial out through zaptel) Replacing this board