similar to: CallPres screening DDI

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hello all, the scenario: Carrier ----S2M------ * -----S2M------Siemens | | SIP Clients and many other features With much help from the list, the PRI links are without alarms and inbound calls are working fine (from both: Carrier and Siemens). But I am not able to dial wether outbound nor to the Siemens PBX. I allways get the message: == Everyone is busy

Hello all, does anybody have experiences with DDI on ISDN BRI? I would like to order DDI with 10 or 100 numbers from telco company, and use DDI numbers for direct calling SIP/H323 clients. But I don't know if Asterisk supports it, in archive I found only one answer about it, and I'm not sure. I am going to use it with isdn4linux card. Maybe DDI is called differently in other countries,

I'm using a TE405p with all four spans enabled, two configured as pri_cpe and two as pri_net, the asterisk is sitting between our ISDN (UK BT EuroISDN30) and our phone system. We have 200 DDI numbers on the ISDN's and I need to give one of our clients dial-in access to be able to monitor calls we handle on their behalf. I've got ZapBarge working but I need to restrict the client

Hi all, Is there in * support for DDI (Direct dial-in)? I buy a AVM ISDN-Controller B1 & I want to use it in point-to-point mode on my ISDN BRI link with DDI preselection. That means, that I have phone number range from ATM, e.g. +421 2 xx xx xx yy where yy I can set-up on my PBX (*) xx - fixed numbers. I want various action for various yy, like (f.e.): 01 -> ring analog phone on TDM

Hi everyone, I want to get multiple DDI's and hunting across those DDI's in case one of the lines is busy using analog phone lines. The system is for a large house so I want 3 x PSTN lines. 3 x DDI's and the ability for those DDI's to be presented across all three PSTN lines. BT say you can't have more than one DDI number associated with a PSTN line and that you can't

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Author: pjha Repository: /hg/zfs-crypto/gate Revision: 1384398963b7f0f86003735b23845a984fe75f5e Log message: 6371650 pci capability ddi iterator Files: create: usr/src/uts/common/io/pci_cap.c create: usr/src/uts/common/sys/pci_cap.h update: usr/src/uts/common/Makefile.files update: usr/src/uts/common/io/pci_intr_lib.c update: usr/src/uts/common/io/pcie.c update:

Hi everybody, I have problems with the chan_capi in the P2P (DDI) mode and it is not possible to use zaphfc, because I need call defelction. This is my capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 language=de ;mode=immediate isdnmode=ptp ; 123456 -0 [interfaces] msn=1234560 incomingmsn=1234560 controller=1

I have * configured with 2 X100P cards (fxs_ks). The lines from the telco are 'analogue both way ddi trunks'. This means that every inbound call contains digits that represent an extension on the PBX. I can make outbound calls from * with no problem however I cannot receive inbound calls on these trunks. Some investigation has shown that when the line is idle there is 50 volts present and

Hi, I'd like to know if and how can I set CallerIDNum for outgoing calls on a PRI line with DDI. Does anyone know if italian Telecom permit this? Thanks -- Domenico Viggiani

You should be able to get ISDN though. I think BT provide this anywhere. Otherwise your solution will be a Primary rate (ISDN30) with 8 channels. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Matt Sent: 07 June 2004 10:19 To: asterisk-users@lists.digium.com Subject: Re: RE: [Asterisk-Users] Multiple DDI &

Dear Xen community, I have Xen 3.0 installed on RedHat Linux Enterprise RHEL4U2. "xend install" runs fine with no error messages. However, when I start "xm cr guest-vmx.conf" I do not get any new window open for the new guest OS. "xm list" shows that the vmx has started and seems to be working fine (just for testing, when I type "xterm" an X window

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Greetings list, I'm trying to establish if there's an issue whereby certain telcos in certain countries have not updated the London, UK numbering plan to include some parts of the 020 3 range, despite it being in operation for some two years now. To help with this, I'd be most grateful anyone outside the UK could make a test call to +44 203 3393 7389. This is a simple test number

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hello all, I really checked voip-info.org but it still seems to be not very easy and I just hope that there is anybody with a simular config. We have one PRI (euroisdn with 30 channels) coming from the DTAG. The second PRI should be connected to a Siemens Hicom 150E Pro Office PBX (was cheaper than a channel bank :-) Carrier ----S2M------ * -----S2M------Siemens | |

FYI >Mailing-List: contact vulnwatch-help@vulnwatch.org; run by ezmlm >List-Post: <mailto:vulnwatch@vulnwatch.org> >List-Help: <mailto:vulnwatch-help@vulnwatch.org> >List-Unsubscribe: <mailto:vulnwatch-unsubscribe@vulnwatch.org> >List-Subscribe: <mailto:vulnwatch-subscribe@vulnwatch.org> >Delivered-To: mailing list vulnwatch@vulnwatch.org

On Tue, Jun 23, 2020 at 06:14:06PM +0800, 雁渡寒潭 wrote: > hello: I yum install libguestfs-tools,when I run virt-builder -l > error: > curl: (56) Recv failure: Connection reset by peer > virt-builder: error: external command ‘'curl' -q --config > '/tmp/virt-builder.sVjrSV/guestfscurl53f9ac.conf'’ exited with error 56 Possibly a problem reaching