similar to: Grandstream Message Waiting light

I've looked through the archives - and see questions similar to mine, but no answers. What, if anything, can be done to get the incoming Caller ID to be presented on the Budgetone's Caller ID display? In all other respects the phone+Asterisk seem to be extremely happy with each other.

Hi I am setting up an Asterisk System in an office environment, Incoming and Outgoing calls are working ok, but i am having a few strange problems regarding call waiting. With the SNOM 200 (firmware 2.02t) phones, if you are on a call and a 2nd call comes in, the call waiting beep is played and the light flashes, but if you hang up the 1st call, instead of the phone ringing, it connects the

Hello, I have a problem with asterisk and Grandstream BudgeTone-100. With default configuration everything works (in anonymous mode and fixed IP), but if Im trying to enable registering, it dos not work. I used 'sip debug' and verbose level 10, nothing happens if I switch telephone on (no messages about bad auth etc). As I understood, after switching phone on at first it will try to

I am setting up a small Asterisk system for use at home. I have one Budgetone 101, one Cisco 7960 and two Xten lite softphones. So far everything is working expect for an issue with the Budgetone. When a call is placed between the Budgetone and any other phone, the call is setup and sounds good. If I hang-up on the Budgetone, everything is ok. If I hang up on the other phone, the Budgetone

Hello guys, I ask you to share your experience with your BudgeTone 100.... I have my asterisk @ work and I've bought a GrandStream BudgeTone (SIP phone) and I usually use X-Lite I have plugged my BudgeTone into my home network because I want to be called even at home. I succeed to register my X-Lite with Asterisk from home but I can't do that with my BudgeTone. (I don't know

Hi, I'm considering giving the Grandstream BudgeTone-102 phones a try. I've been using Cisco 7960's to date, but the low cost of the Grandstream phones are hard to ignore. I have two questions: 1) Does the message waiting indicator on the BudgeTone's work with Asterisk? 2) The one line 12-digit LDC concerns me a bit. Is the LCD able to display both the CID number and name on

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040709/2e9bd3f6/attachment.htm -------------- next part -------------- ? Hi there, This is shan. I need help regarding the grandstream Budgetone - 100 phone which i configured. My problem is: I can able to do call ---> Softphone(PC) ---> * ---> Grandstream Budgetone-100 but

Does anyone know what the Grandstream Budgetone is going for $$$ in the US? I didn't immediately see pricing on the phones page. AJ

Symptom: Phone after about 15mins will stop functioning Problem: DHCP lease renewed but default route dropped Fix: Assign a static ip and problem is resolved. Upgrade to new firmware once it is released It turn's out that these phones have a few issue in 1.0.3.81 firmware. The phone may stop transmitting packets if configured with DHCP, if DHCP is being provided by certain devices. Netopia

I have two problems with Asterisk and my Budgetone 100s. 1. Sometimes when outside callers dial my Budgetone it will ring twice, then the caller will receive a busy signal. This happens intermittently and I cannot pin down the circumstances of when it works and when it doesn't. Asterisk logging doesn't give me too much info when this happens: *CLI> -- Executing

Is anyone using this combination successfully? I have a dell 500sc running rh9 and asterisk 1.0rc1. It is configured with an x100p. I have a Sipura SPA-2000, laptop with Xlite and a Grandstream Budgetone BT-101. I have signed up with Voipjet (they use iax2). I also have an FWD number via iax2. I can sucessfully call back and forth to all devices via zap, sip, and fwd. I can successfully

Hi everyone, This is off topic and is for GS technical support really but it seems that there are a lot of Budge Tone 100/101/102 users out there. I've got a Budge Tone-100 (101 - without the extra 10base ethernet connetion?) here. I changed the configuration through its web based interface and I clicked the reboot link. But then something went wrong and ever since then it doesn't

I bought three plus two Grandstream BudgeTone 101 phones. The shipping cost more than the phone itself from Pulver store. The first shipping had one phone defect. Nothing on the display. (Can happen!) The second shipment had one phone with a defect display, but it still worked. The second phone's handset was defect too (microphone did not work). Changing the handset from this one to the

Hello, I have been working on getting Asterisk up and running with a couple Grandstream hard phones (Budgetone 100s) and a couple softphones. Things work pretty well but we have discovered an odd problem. A calls B and then A can put the call on hold and pick it back up. A calls B and B can put the call on hold but cannot pick it back up. These tests are internal on the hard phones. The

I'm trying to fix a problem with the GrandStream Budgetone 102. I've been reading the source code, mailing lists and other resources. Here's the scenario and the approach I have been pursuing. I'm having some problems with the AGI calls and I hope someone can give me some clarification. PSTN <---> T1,PRI * <---> Grandstream BT 102 (12)

Hi there, I'm having problems with the Grandstream Budgetone 101 on hangup - "show channels"/"show channels concise" output is still showing the call's channels as active. The problem does not exist when I use SJPhone, so I'm assuming it isn't an Asterisk configuration issue. Has anyone seen this, or better, does anyone have a fix? :) Thanks, David. --

Hello, hope somebody can help. I have setup a queue which maps to some Budgetone SIP phones. When a call is answered, the # key to transfer a call does not work. Everything else regarding the queue works fine. Is there a way to activate it? Maybe something like the t option in the Dial application. Thanks in advance, Christian.

I have a cisco 7940 with the following sip.conf config: [Desk1.1] type=friend secret=****** defaultip=192.168.1.14 insecure=no mailbox=102 callerid="Desk1.1" qualify=500 canreinvite=no context=extensions host=dynamic group=2 I do not get message waiting indicator (mwi) on this phone. Is the another .conf file invilved in configuring this function other than the mailbox=xxx in the

Hello, Anyone using the 1.0.4.55 firmware release with any success? I have had my Budgetone running 1.0.4.50 for about a month and a half now with no problems whatsoever, and I am a little leary about upgrading. -- Vice President of N2Net, a New Age Consulting Service, Inc. Company http://www.n2net.net Where everything clicks into place!

Hi Just 2 issues I have with SPA841. 1. I autodial extension 600 then inside an AGI wait for more digits. The digits are transmitted correctly to * but they do not show up on the SPA841 display, only the 600. How do I set the 841 is show the digits after the 600# 2. Is the SPA841 pixel display backlit? Master