similar to: Asterisk PID file

I haven't seen anybody so far post a complex fix for the udev problems on FC3 with the latest kernel. On that note, I have a temporary fix to allow zaptel to load somewhat normally. I found that modifying the zaptel script to 1) load, unload, then load the driver modules and 2) insert a pause between modules seems to allow things to work. This assumes you have followed the instructions

I have put a box together using 2 X100P and 2 TDM400 4port cards. Using the simple setup that Martin posted a few days ago, I have asterisk almost up and running. /etc/zaptel.conf fxsks=1-2 fxoks=3-10 loadzone=nz defaultzone=nz (I have added NZ tone information to zaptel and Asterisk - I'll submit a patch soon). /etc/asterisk/zapata.conf [channels] context=incoming signalling=fxs_ks

HI, I just installed an additional module to a TDM400P card. Everything worked fine for a while, but after rebooting the server the new channel fails to be recognized by asterisk. Here is the output == Parsing '/etc/asterisk/zapata.conf': Found -- Registered channel 1, FXS Kewlstart signalling -- Registered channel 2, FXO Kewlstart signalling -- Registered channel 3, FXO

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

Dear list, I am trying to learn how to use Zap-things in Asterisk. While loading Asterisk verbosely I get this error: [chan_zap.so]Warning, flexibel rate not heavily tested! => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Mar 12 17:19:01 WARNING[5563]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or directory Mar 12

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

Hello, I ordered the Devel lite kit, and installed it. I am just trying to get the FXO port to work, and am having trouble. To load the card I do the following. modprobe wcfxs modprobe wcfxo ztcfg -vv asterisk -vc My /var/log/asterisk/messages show Nov 3 11:03:39 WARNING[3317]: zt hook failed: Device or resource busy Here is my /etc/zaptel.conf fxoks=1 fxsks=4 loadzone=us defaultzone=us

I have just a second case where after * had been up for a few weeks working perfectly, it suddenly stopped talking to all the extensions. The I4L was still working perfectly though... I tried to stop asterisk, rmmod the modules, and insmod, and re-start asterisk but it did this: Using /lib/modules/2.4.21-pre5/misc/zaptel.o Using /lib/modules/2.4.21-pre5/misc/wcfxo.o Using

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

I've been having trouble with a TDM10B that I installed a few days ago. At first I could not modprobe it at all (getting the errors below). I switched the X100P that was also installed (with a Motorola chip) with one with a Tiger-something chip, and then everything starts up okay. However, after a few hours, the FXS port dies (no battery or anything), and if I try to rmmod & modprobe

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

It's nice to be able to define the list of asterisk modules we want to load from the /etc/sysconfig/zaptel file rather than directly in /etc/init.d/zaptel. I'm using nufone and don't require anything but the ztdummy (is the rtc-based module better, anyone?), so that's what I've put here. These are based on zaptel-1.0-RC1. John --- zaptel-1.0/zaptel.init.ole

Hi list. I'm having the next problem. I have a * with 1 TDM400P (4 ports) and one X100P, with a working configuration. Today i add one more X100P card, and i change the config files as next: zapatel.conf: fxsks=1-2 fxoks=3-6 loadzone = us defaultzone=us zapata.conf ... context=bell

Well, I got my nice new 4 port FXS card this afternoon, and with all my other asterisk problems, decided now was a good time to throw it in.... So far, I have dropped it in, done a clean cvs checkout on zapata, zaptel, asterisk, make clean and make install on each. I can load the wcfxs module which finds the card (though one time it failed the register check and locked the machine up, a hard

I'm having sporadic problems with my X100P card. When trying trying to call out I get a message on the console that the channel is busy even though I have bounced asterisk. It seems the card grabs the line and doesn't let go. When I try to call the number I get a busy signal. If I perform a rmmod wcfxo and restart asterisk everything retruns to normal. I have a TDP400P installed along with

Could anyone with any experience with * over a non-PRI T1 help this newbie? I have a fractional T1 that is working fine through a channel bank, but I can't get any response on * using a T400P. My analog line and the extensions work fine, but the T400P port 1 shows a red led (what exactly does that tell me?). I brought up zttool which shows a condition red also, but ztcfg shows nothing amiss.

Hi, I finally was able to to get samba/winbind to authenticate off W2k3 Active Directory. I seen a lot of info on the web on how to do this but I never seem to have one site that got me through it all. Anyway, with all the info I gathered I was able to put it all together, get it working and documented all the steps I used. I'm running Redhat 4 (2.6.9-55.0.2) with compiled Samba 3.0.25c

I'm not the most experience Linux user on the block so please excuse me if this is an easy fix. I noticed the other day while looking at my active services that Icecast has started more than once on my server. I'm wondering if someone would be able to look at my config and tell me why this is happening, or how to stop this from happening. My guess is that since I'm binding to an IP,

Hi, I noticed one small possible error in the openssh-2.3.0p1/contrib/redhat/sshd.init script. In the stop option: stop) echo -n "Shutting down sshd: " if [ -f $PID_FILE ] ; then killproc sshd [ $RETVAL -eq 0 ] && rm -f /var/lock/subsys/sshd fi echo