similar to: Problems calling a phone number through a X101P card

Hi, I'm a newbee to all this asterisk stuff, and after reading a fair amount of docs at the voip-info wiki, I was wondering if it will be possible to work out something as the following scheme: A B +-----+ +--------+ +----------+ +---------+ | SIP | | | Internet | PC | phone line | classic | |

Hi! I'm trying to compile libiax2 on windows using msvc6. In the libiax2\src\iax.c file, line 670, I'm getting a: error C2229: struct "__unnamed" has an illegal zero-sized array It seems to complain due to the last member of iax_frame. Does anybody knows what should I do to make it compile? FWIW, it compiles fine using gcc on cygwin. Thank you in advance for any tips!

1. I noticed that... - after cold booting the host, I see successful Dahdi/wcfxo messages in /var/log/messages - then, if I run either "/etc/init.d/dahdi restart", or "/etc/init.d/dahdi stop; /etc/init.d/dahdi start" without waiting more than about 10 seconds between the stop/start commands, I get the familiar error messages "DAHDI_CHANCONFIG failed on channel 1: No such

Hello I'm using an older PC from 2000 that we have lying around at the office to learn about Asterisk using Pound Key 1.0.1 (http://www.rpath.org/rbuilder/project/asterisk/). It's using an AMD Duron 600MHz, a Gigabyte GA-7ZX motherboard, and two FXO Astralis X101P clones that I bought through eBay. Here are the three issues I have. Sorry, forgot the floppy with dmesg, lspci, and

Hi, I installed a 1-port FXO on my Ubuntu 8.4. I was earlier only hearing a fast clicking sound and now I am not hearing any dial-tone. The FXO card has 2 slots: [phone | line ]. I hve connected the wall-phone-input to the "line" slot and "phone" to my home-phone. I do not hear any dial-tone on my home-phone. Asterisk seems to recognize my hardware....here are the relevant

I've had a few problems with my system holding the line after a call has been made, just now I rebooted and noticed the following in /var/log/messages Aug 13 17:23:15 Sheriff kernel: wcfxo: DAA mode is 'FCC' in the file wcfxo.c the following structure is initialised as below which would suggest that FCC is wrong for France or pretty well all of Europe. static struct fxo_mode {

I am finding that I have to increase the txgain in zapata.conf to 8 when my X101P is connected to my BT phone line, otherwise people can hardly hear me. This then gives echo issues. Do other people have the same problem on BT lines. I was wondering if I should give BT a call and get them to increase the gain on the line. Strange though as the rxgain is OK and I don't have this problem with

Hi Perhaps people with more logic/electrical knowledge then I could address this....

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a

Por favor podrian ayudarme con esos paquetes (hydroTSm-hydroGOF), si tienen algunas ayudas con las escrituras para ejecutar los comandos de cada uno de ellos seria excelente, necesito mucha ayuda en esto, desde ya muchas gracias saludos -- *Diego G. Mejía V. Medio Ambiente-Universidad Nacional de Loja* *Grupo de Ciencias de la Tierra y del Ambiente (GCTA)* *Investigador* *Universidad de Cuenca*

I'm having no end of trouble with some Siemens Gigaset phones and GS HT286s. Gigaset 100 and 3010 phones work perfectly, but a 4010 only rings once then it goes off and then just flashes it's LEDs and displays "incoming call" on the LCD with no further ringing. According to the manual it is CTR37 but the only setting on the GSs is CTR21, I've tried different cables but some

Hi, I'm not sure if I just missed something somewhere along the way, but I noticed while I was going through the CVS logs that there is an option in the wcfxs module to set an "opermode" - which apparently might help with echo issues around the globe (like the ones I'm seeing - some times). So I'd love to use it and give it a go. Apparently, there are some options that

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

Hello The Ubuntu Asterisk package doesn't install /etc/modprobe.d/dahdi.conf, so I was wondering where to put the following line: ======= options wctdm opermode=FRANCE ======= Should it be in /etc/dahdi/modules? ======= options wctdm opermode=FRANCE ======= Thank you.

Hello All... I have searched in the archive and also followed Zara's instruction on getting incoming calls to work with Asterisk...but I still can't get Asterisk to answer incoming call on Linejack's LINE port. I attached a phone set to the PHONE port, and telco line to the LINE port on the Linejack(ISA) card. I have downloaded, compiled and installed the newest driver for

Hi All; If I need to set the opermode to King Saudi Arabia, what the name I have to use? For example, to set it for kuwait then I use opermode=KUWAIT. So what will be for Saudi Arabia? Any advise? Regards Bilal

When x101p clone receive ring signal from phone line, my voip phone start ringing. But, if caller hang-up at some time, phone continues to ringing 10 second more. How can I shorten that time? Pause betwen incoming rings on my phone line is 4s, so when x101p clone (wcfxo driver) do not receive next ring signal after 4.5 sec, call should be consider as ended. What should I change to set that time

To all: I am researching the feasibility of replacing our current PBX (ATT Partner Plus) with an * PBX. I have purchased an X101P card and I have * running of a FC2 machine. The X101P is connected to an extension on our current PBX. Many archives exists regarding X101P cards but I just need some guidance. First the X101P did not detect a ring, so I found an email where someone

X101P with Ambient md3200 chip on it, with the zaptel wcfxo driver.... Just an indication of how many people have got this to work would be useful. Cheers Mark.

Could someone please assist me soonest. when i run asterisk with one X101P card and a S400P card asterisk will run but the card will not work.this is the message i get: [format_jpeg.so] => (JPEG (Joint Picture Experts Group) Image Format) == Registered format 'jpg' (JPEG (Joint Picture Experts Group)) [cdr_csv.so] => (Comma Separated Values CDR Backend) [cdr_mysql.so] =>