similar to: TE410P -> Dialogic D240SC

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

I recently purchased a Sipura 2000 and connected a phone to it which is connected to my asterisk box via sip. Calls to the Sipura 2000 work fine from another sip device connected through *, from either an fxo or fxs (via adtran channel bank connected to a T400P card) port. However, when a call comes in from the phone company over a T1 with em_w trunks, the phone on the Sipura will ring but I

I'm trying to connect an Asterisk T1 port to a Dialogic card. The Dialogic side is an external VMS. I setup for ISDN-PRI between systems and have green lights on both card/ports. Zttool shows connection is good also. However, when I try attempt terminate or originate a call to either system, nothing appears of CLI. How can I monitor the "D" channel? zaptel.conf: # Span 8:

Tie line is type em_w (old school stuff) to TE110P. Phone rings on the asterisk side, but the calling party does not hear the ring through sound. If I pick it up within the first two rings it goes through and I can talk otherwise our old switch drops the call. Anyhow...here is my config if anyone can shed some light on it. It used to work with HEAD a few weeks ago. -Matt

Hello, I am installing asterisk, libpri and zaptel. I have it setup for EM wink. incoming calls are working. outgoing calls are not. zttool shows TxA as 11000000 RxA shows 00000000 This doesnt seem like em_w signalling? Seems like the PBX is not setup for EM_w. Is that the case? Jerry

Hello, I have a T1 (not PRI) plugged into my Asterisk server. Everything is working well, except I only get the first digit of the 4 digit DID in Asterisk. The T1 provider (Eschelon) tried switching to 7 digits, and I only got the first digit of the 7. Can anybody help? We're adding another DID and I need to trap it correctly. Thanks. Here are snippets from the relevant files: --

Hello list, We have some kind of a problem with our Asterisk installation. We want to be able to publish different caller id when placing outbound calls through the PSTN. We have Asterisk with TE410P and T1 from FDN Communications. The problem is that all our outbound calls show our main number, regardless of what we set with SetCallerID, even using CallingPres with all possible

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

When I send a call from my TE410P using E&M, the legacy PBX answers the call but doesn't route it. Any idea what this could be? I assume the digits aren't being delivered properly to the legacy pbx. Any suggestions on what config settings to muck with? Asterisk SVN-branch-1.2-r40901 built by root @ pbx04 on a i686 running Linux on 2007-01-14 14:05:02 UTC zaptel.conf

I currently have Asterisk deployed in my office with a TE411P. On the first port of this card is a T1 from the telco setup for D4 AMI. Unfortunately, I'm not receiving caller ID on inbound calls from this line. The caller ID information is arriving in the form *ANI*DNIS*. In zapata.conf, I have signalling set to em_w. The DNIS always arrives correctly, but I'm never receiving the ANI

Hello, We just had some new T1s turned up today to replace others that our contract has run out on and we are now getting more echo on the new T1 lines than we had on the old ones. The T1 type is 24-channel, D4/AMI SF Robbed-bit(the same as the T1s they replaced) The problem is that we are getting echo on about 10% of the calls in and out placed on these new T1s compared to less than 1% with

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

I've got a new setup (different building) where Asterisk is sitting between the PBX and phone company on a E&M T1 line. Mitel PBX <-> Asterisk <-> Phone company Inbound works. Asterisk gets the in-band digits from the phone company and hands the call off to the Mitel just fine. Outbound is weird. Asterisk seems to expect that the mitel will send routing information

Hello all- So I have * up and running and connected to a legacy system via em_w lines and have no trouble dialing from * through the tie line but from the PBX across the tie line I am having intermittant receipt of the DTMF. T-Berd testing is showing that the digits are coming across but * is either missing the first digit consistantly. This seems to me to have something to do with start timers

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

Group When I dial a phone number that should go out to the telco my local phone rings. Does anyone have any hits ? Thanks Asterisk Ready. *CLI> -- Called g1/6144196143 Urgent handler Urgent handler -- Starting simple switch on 'Zap/2-1' Urgent handler Urgent handler -- Called 6149236651 Urgent handler -- SIP/6149236651-1d93 is ringing Urgent handler -- Zap/1-1

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent