similar to: General advice on confs and setup for new users

I'm looking to get an x100p off ebay and am not particularly familar with the "life cycle" of the card.. An "Authentic X100P" listing has a buy it now of $29.95 and says There are 3 types of cards Asterisk would recognize: *Screenshots from the official, original driver install Cheap "OEM X100P","Clones", "Compatibles", Knock-Offs

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

I am starting to dip my toes into the asterisk world, and to that end I've scavenged an old PC (this is a home project, and I have basically $0 to spend on it), and installed FC1. I've purchased a clone X100P (or at least I was told it was), and I am trying to get it to work. However, when I try and load the wcfxo module, I get the following errors... [root@loudhoward root]# insmod

Hello All, I installed Asterisk@Home .5 last night. I was able to configure some extensions for the house and they work fine. I just can't make inbound and/or outbound calls. The Flash Operator Panel shows four external icons and my new extensions. I have four X100P and two Broadvoice sip accounts. Thanks, David -- David Shaw <asterisk@ke6upi.com>

Hello all, I have just installed a Wildcard X100P into an Asterisk box. I connected the line socket to the internal telephone system where I work. The card is identified to asterisk etc, however I am unable to recieve or make calls. When attempting to dial I get: Executing Dial("SIP/1106-ec8b", "Zap/1/644746") in new stack Called 1/644746 Zap/1-1 answered SIP/1106-ec8b Hungup

Hello All, I have a very small setup of 4 users and a X100P. Asterisk is currently running on an Athlon 1800 but the server it is running on is also our imap/web/mail/development/samba server and we are having a few issues with asterisk which I believe is down to to many tasks. What I intend to do is build a box just for asterisk(Ill call the old one obelix). I have a few machines in the loft

Hi All... I have installed a single X100P card in my PC and am playing with Asterisk. The wire I plugged into the X100P has two POTS lines on it, wired on the RJ45 in the normal way. I am getting odd behavior. It seems when I dial out that the X100P dials both lines at the same time. I have two questions. First, I see that the X100P is only a single channel. Does this mean that I can

Hi. I have been searching through old threads and various forums, but can't seem to find out what the consensus view is here on the best type of FXO hardware to use for a home asterisk implementation. Specifically, should I buy a FXO ATA like the Sipura 3000, or a PCI form factor port like the Digium TDM400 series. I have read horrible things about problems with the X100P, so I have ruled

Yo all, I have a problem with a Dutch (KPN) PSTN-line, connected to an X100P. The call wil sound OK at first, but after 10-20 minutes, the audio will start to crackle. Soon after that, this crackle turns into a continuous noise and the parties won't be able to hear eachother anymore. It also sometimes happens that the party on the TDM400P hears a very loud, short-delay echo of themselves,

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

Hello, Can anyone tell me what the "normal" number of interrupts per second is for an X100P card? I've used FreeBSD 5.3 and a linux 2.6.11 kernel on the exact same hardware (only the disk changed) and `systat -vmstat 1` on FreeBSD and `procinfo -dS -n1` under Linux. For both, I'm seeing roughly 1000 interrupts per second on my X100p card. It was a bit worse under FreeBSD, and I

Hi I thought this might be of general interest. Recently I purchased an X100P from a Digium reseller in the UK. Very pleased with the card; works perfectly. My friend (known for his deep pockets and short arms) purchased an X100P card from Ebay. He's had no end of problems with line noise, dropped called etc so I thought I would compare the two cards. Plus mine was delivered within two

Hi all. I`ve installed a X100P on my box and is working well with incoming and outgoing calls as a trunk with one PTSN line. I want to connect the X100P to my Panasonic 616 EASA-PHONE as an internal extension to permit to users to make calls to SIP devices from analog phones, the problem is when I dial the ext number where the X100P is connected I get busy tone. What config I need to change to

Hello my brothers and sisters, Is "X100P" card suitable to VoIP? and if "yes", am i need to only "X100P" and "Asterisk" Package? or i need also to other cards or packages? and if "X100P" card not suitable to VoIP, please recommend a another card, (please take in your account that i would like to connect standard analog line to the card

Hello, I have X100P card but exten => _9X.,1,Dial(Zap/1/${EXTEN:1}) does not work. The error is app_dial.c:803 dial_exec: Unable to create channel of type 'Zap' (cause 0) Zap show channel, lspci etc show everything is normal. Because X100P is Intel 537 modem, so can I use it as true modem for test? Did any one use X100P as a modem? Thank you very much. -------------- next part

Hi all, Really excited to be using Asterisk and learning about VOIP and PBX's. I'm a complete beginner at telephony but have built and installed Asterisk 1.4.5 and read several of the Asterisk books online and have successfully connected to FWD with IAX2 and to GIZMO using SIP. Just purchased a Motorola Wildcard X100P and installed it into a clone PC running Fedora Core 6. Analog

Folks, For the last few days I've been trying to experiment with a Panasonic PBX and an X100P but have run into quite a few problems which I am not sure if they can be solved with this type of card (how about TDM01B?) 1) I wanted to use *'s IVR capabilities, so I routed the calls to the extension where the x100p was connected to. Asterisk should answer the call, playback a message,

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

If Asterisk is configured as a simple answering machine replacement with the X100P connected to PSTN line. No FXS ports in the Asterisk machine. Standard phones are connect in parallel with the X100P like you would a regular answering machine. Can Asterisk detect that a phone has been picked up and cancel the outgoing message and/or voice recording? What about if the phones are connected to

*** Now you just need a "phone" or "station" (FXS) device and a method of connecting it. *** So... essentially I need to spend another $125 US on a Wildcard TDM400P so I can plug in an analog phone? On the X100P description it says: "The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end disconnection supervision). It can detect ringing and