similar to: 2 T100P cards - 2 switch types

Hello, I'm trying to get a Wildcard T100P working with Asterisk and so far I haven't had any luck. No problems with the card itself from what I can see and the telco says that the problem is on our end (don't they always?). A small sample of what asterisk spews out on the console: Jan 13 15:45:32 WARNING[180236]: chan_zap.c:5834 zt_pri_error: PRI: Read on 43 failed: Unknown

> -----Original Message----- > From: Jerry Geis [mailto:geisj@pagestation.com] > Sent: September 8, 2004 2:19 PM > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] T100P calls with playback starts speaking > before pickup > > > Hi > > I am using a T100P connected to a panasonic phone switch using T1 and the > switch has 4 analog lines

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

My PRI is being reset at least once a day with the following errors in the logs. zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has been happening for weeks on all versions (including -stable). the T100P card appears to NOT be sharing an IRQ. xenon# cat /proc/interupts CPU0 0: 1203977 XT-PIC timer 1: 3 XT-PIC keyboard 2:

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Hello, I have a T100P card on a Red Hat 8 machine with Asterisk installed on it and I'm trying to get the data routing properly through it. I purchased an Integrated Data/Voice T1 Line with channels 1-6 voice and 13-24 data. The line is plugged directly into the Asterisk machine's T100P card. Previous to the asterisk set up we had an Adtran router that connected everything to what the

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Hi, I'm seeing a problem when calling into my Asterisk server from a T100P with PRI signalling. I'm hoping someone has seen this as well, however, it's a little hard to explain. When I'm navigating through Asterisk on an inbound call from the PSTN, I'm getting a random 'noise' during the playback of sound files. The best way I can describe this noise, is imagining a

Hi all, I have a Wildcard that is flip floping between internally clocked and the PRI. It is showing Red Alarm/Recovering. After a long run around with the telco, they said I have lost the D channel on my side. I am seeing this message: == Restart on requested on entire span 1 Sep 21 08:29:48 WARNING[1192491824]: chan_zap.c:5942 zt_pri_error: PRI: !! Got reject for frame 1, but we only

Don & others, Thank you for your answer. The fog maybe lifting ;). The zaptel.conf file has the following in its comments: # # The timing parameter determines the selection of primary, secondary, and # so on sync sources. If this span should be considered a primary sync # source, then give it a value of "1". For a secondary, use "2", and so on. # To not use this as a

Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank | | |

In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Due to some failed hardware on another platform, I've had to move a T100P card to a different chassis. After this move was completed, I am seeing some strange results on the T100P card that do not display to me any failure mode with which I am familiar. The card comes up, and shows "good" carrier and status, but Asterisk refuses to bring the D-channel up. Calls of course do

All, Alright, I've looked around the internet, the voip-info.org wiki, and browsed the contents of this mailing list. While I've found a couple of scenarios that are close to this one, I haven't found one that uses my particular card (T100P). Without further delay -- I have successfully configured internal SIP services between a Snom 200 and a Windows X-Lite client and have

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

I've been having some problems getting a channelized T1 working with a T100P card. Perhaps someone can help: I have an Eschelon T1 coming into a Vina Integrator box. This box splits out the T1 into an ethernet plug for bandwidth and a secondary T1 which I plug into the T100P card. I've connected the two with a T1 crossover cable. I get a green light on the t100p card and can make