similar to: TE410P / Eicon PRI

Well, I have to confess that I am disappointed that in a fairly high volume list like this, I haven't had one reply to the questions I've asked. (I know I haven't got any right to expect a reply, but communities are usually fairly helpful). It might be really obvious to you guys, but if you have not a lot of experience with ISDN/PBXs, it's hard to understand. I'm going to

Hi, one short question: Is it possible for the zaptel driver to deal with multiple phone numbers on one single E1 PRI line? I could make my carrier route +49 xxx aaaaa-zzz and +49 xxx bbbbb-zzz and others down one single PRI trunk to our asterisk box terminating in a Digium TE410P. Does the driver handle this and can I put calls coming in all on the same physical interface put into

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Hi *, I want to integrate the Eicon Diva 4Bri Card to Asterisk. Eicon drivers and capi is installed. I use the latest dev version from eicon compiled and installed for my fedora 2 system. I found the chan_capi for asterisk from www.junghanns.net. Also loaded the patch and applied to the chan_capi source tree. I changed the Makefile to include the capi20.h from eicon:

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hello Everyone, I am once again wondering about EICON. I have had no success with the Diva Pro or Diva Pro PCI, so my question is, does anyone use an Eicon Server BRI card on Asterisk? Or would I be better off trying to get a split PRI? Regards, Greg

Hello, Does anyone know what driver to use with an "Eicon Diva Server 4BRI" card? My modem.conf: -------------- [interfaces] context=remote driver=i4l msn=16453 device => /dev/ttyds01 -------------- I get the following error: -------------------------- == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem Driver) WARNING[8192]: File chan_modem.c, Line 383

Hello, I try to use Asterisk with an Eicon-card called "DIVA Server 4BRI-8M PCI" but I don?t get it to work. I?m running on RH8.0. The Eicon-card supports isdn4linux. In the modem.conf file i have put following: ----------- [interfaces] ; By default, incoming calls should come in on the "remote" context context=remote ; Modem Drivers to load driver=i4l ; Type of dialing

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

I know this has come up before but... Has anyone done anything to get an IAX client built on Windows? I thought someone had started one, but I haven't heard anything about it since - and that was months ago? Anyone have any idea what the status is? -- Ron Gage - Saginaw, Michigan I am looking for work - resume at http://www.rongage.org/resume.doc Electrical Engineering, Linux Programming,

Hi all, I have a box running asterisk with T410 connected to a Nortel DMS 100 switch and another box running SER with grandstream phones on it So if there is a call from the pstn it goes from the Nortel to the asterisk and then to the SER box and finally to the phones.if the phone is busy or the number is invalid the * box will first send an ALERT message to the Nortel and say the call is going on

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

I found this tool, but didn't have the time to test it... http://www.dylogic.com/sito/ArticlesDMD/mirial.html -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com]On Behalf Of shabanip Sent: donderdag 24 juni 2004 13:59 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Video/H323/SIP Is there any software based

Hi there I am in the UK.. and am running latest asterisk on FC1 (2.4 kernel). I would like to know what the best option is for a 4 port BRI card. I notice Digium don't provide one.. I have heard the Junghanns do one...but are there others ?? Is the Junghanns card reliable/stable with good sound quality ?? I notice it is very expensive in a per port comparison with the Digium cards.... hence

Having ISDN FXOs and a bunch of ISDN DECT base stations, I went looking for a CAPI compatible active BRI adapter capable of NT mode. I have found that the 'Eicon Diva Server 4BRI' fulfills theses requirements. However, at EUR 1387 for four BRI interfaces, it does not come cheap. Are there other users of similar hardware that can point me to alternatives ?

We are located in Belgium and just ordered a PRA line, the telco asked the following questions : - 120 or 75 ohm ? - Support for CRC4 yes/no ? - B channels in 2 way ? We will buy a digium card but which one should we buy ? could anybody help me with this ? Thank you Michael Sorry for the previous html mail DISCLAIMER: The content of this e-mail message does not constitute a commitment

In belgium people can receive SMS's on fixed lines, my question is if this feature is possible on the digium TE410P card in combination with asterisk ? Kind regards Michael DISCLAIMER: The content of this e-mail message does not constitute a commitment of DKMA bvba This e-mail and any attachments thereto may contain information which is confidential and/or protected by intellectual

Hi all, I need your lights :) There are many hardware provider for E1 cards on the market, what's your exeperience with E1 and what's the preferred provider for Asterisk out of Digium? Olivier

Hi everybody, I will receive my CISCO 7960G tomorrow. I've ordered it as a "global spare" without any callmanager licence. Now I don't know if I can get firmware-updates so could please someone send me the SIP-firmware? Is the default firmware the "skinny" one? Wich would be better to use with asterisk? Thank you very much

Hello all I found a bug in the chan_capi driver (really a not implemented message handling and then a false error condition) and I guess I have wrote a patch to fix it (basically I searched the internet for other capi open source implementation an borrowed the code snippet) but I don't know where to send the report and bugfix. I also found some miss-behaviours that I would like to share