similar to: TE410P in Austria

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31

Dear All, we have installed a TE410P card on a Dell Poweredge 1750 running a slackware 10 with 2.4.26 Kernel. Then we have made two loops on the card and we have configurated all the 120 channels. Our goals was to perform some stess tests even if in this scenario we used the same box as generator and target. The stress test comprised to generate up to 60 calls at the same time by placing a file

Can't anyone stop self-promotion and tell the poor guy what he needs. A T1/E1 X-over cable using an RJ-45 (8-cond.) is pinned out as follows: 1 - 4 2 - 5 3 - NU 4 - 1 5 - 2 6 - NU 7 - NU 8 - NU NU = Not Used I have not in my experience seen any problems with using a Good Quality Cat5 vs. Cat 3 (telco standard) cable for X-connects. YMMV, but you should be fine. As far as the shielding

We have a machine with a TE410P in it acting as a client to route calls via iax2 to our central server, caller --> ( zap -> iax ) ---> ( iax -> whatever ) --> called client server often the called can't hear the caller (both machines on public ip) 'iax2 show netstats" on client machine shows more and more dropped packets on the

We have a te410p, with the following connections: span 1 connected to a 32 Channel EuroISDN span 2 connected to a card in a legacy pbx (Meridian) span 3 connected to a 10 Channel EuroISDN span 4 connected to a card in a legacy pbx (Meridian) We have no need for the meridian now, and decided to turn it off. I did not change the zaptel.conf settings, nor the zapata.conf settings. When the

Hello all, I really checked voip-info.org but it still seems to be not very easy and I just hope that there is anybody with a simular config. We have one PRI (euroisdn with 30 channels) coming from the DTAG. The second PRI should be connected to a Siemens Hicom 150E Pro Office PBX (was cheaper than a channel bank :-) Carrier ----S2M------ * -----S2M------Siemens | |

asterisk-users Any help will be appreciated. This card did not connect with E1 line how to loop E400P card to test ? now I loop the card. span 1 ---span2 RJ45 pins 1--4 2--5 but show : When calling ,showing error: app_dial.c:764 dial_exec: Unable to create channel of type 'Zap' Asterisk Ready. *CLI> -- Registered SIP '2002' at 192.168.139.59 port 3289 expires 120

I have my peers registered to SER.asterisk seems to be sending mwi for the peers seen in the sip show peers CLI command. i have my ser server registered with asterisk as a type=friend and all clients register to ser.how do i get mwi to work for these clients registered to SER. Thank you, -AA

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

hi all, i am getting crazy with my TE410P - it won't work now we already think that the only thing which can be wrong is the cable. At our telecom endpoint we have 1-2 tx, 4-5 rx So - which cable do i need to get it working Already tried a cross over cable 1-2 -> 4-5 / 4-5 -> 1-2 (with this cable nothing works -> red alarm on both ends) Also a normal cable 1-2 -> 1-2 / 4-5 ->

Hello, I have a problem with Asterisk, on 10% of incoming calls the IP Phone ring but I don't hear the caller and the caller doesn't hear me (all IP Phones have the same problem). This problem appear also if the call is directly send to the second E1 of the digium card who is connected to an IVR. It does not depand on the charge of the server (I have the problem with only one call).

hi all, i am trying to get my TE410P (see previous posts) working in Austria (telekom Austria - i am still waiting for an answer for my questions). my /etc/zaptel.conf looks like -------------------------------- span=1,1,0,ccs,hdb3,crc4,yellow span=2,2,0,ccs,hdb3,crc4,yellow bchan=1-15,17-31 dchan=16 bchan=32-46,48-62 dchan=47 loadzone=at defaultzone=at -------------------------------- after

Hi, now that these cards have approval in Australia, has anyone had any luck in connecting them to a Telstra Onramp 10 service? Are these configured as a PRI, bchan=1-10, dchan=16 in zaptel.conf and switchtype=euroisdn in zapata.conf? Better yet anyone have any of the above .conf files they could share? Is an onramp 10 what is referred to as a 'channel bank'? Craig

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

This afternoon I finally figured out more with regarding to a strange clock-slip problem we have on our asterisk box. We have two TE410s, in E1 mode: TE410P version c01a009b They have their own interrupts: 66: 781648298 783747388 IO-APIC-level t4xxp 233: 253890977 1311504670 IO-APIC-level t4xxp They have their full 31 channels: span=3,0,0,ccs,hdb3,crc4 bchan=63-77,79-93 dchan=78

First of all sorry for the little offtopic post :-) For one of our customers i need to make a vpn between the Netherlands and Hungary. Over this vpn two * machines are gonna talk IAX and employees in Hungary are gonna use the Exchange server located in the Netherlands. So far no problem... The problem: I'm from in the Netherlands and don't understand the .hu websites :-( First question:

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

Hi below are my configs: pstn(e1)--->asterisk (span1)----->legacy pbx(connected via span2)-----> legacy pbx analog extensions. my dial plan is like callers dial into asterisk(span1) , hear an IVR option and they are connected to the agents via the legacy pbx (which is in sync with asterisk on span2)....This works perfectly fine until about 200 calls or so...After that time when asterisk

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --