similar to: direct dial-in (DDI)

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi ! I've fetched a spare AVM B1 card from the cellar, and installed it. After "modprobe b1pci" I did "capiinit" and capiinit moaned about a missing t1.b4. So I search the web and found one at http://www.avm.de/ftp/cardware/b1/x_misc/ddi/. When I now look at the controller, I finally see p2p-mode: # cat /proc/capi/controllers/1 name b1pciv4-a400 io

Hello all, does anybody have experiences with DDI on ISDN BRI? I would like to order DDI with 10 or 100 numbers from telco company, and use DDI numbers for direct calling SIP/H323 clients. But I don't know if Asterisk supports it, in archive I found only one answer about it, and I'm not sure. I am going to use it with isdn4linux card. Maybe DDI is called differently in other countries,

I'm using a TE405p with all four spans enabled, two configured as pri_cpe and two as pri_net, the asterisk is sitting between our ISDN (UK BT EuroISDN30) and our phone system. We have 200 DDI numbers on the ISDN's and I need to give one of our clients dial-in access to be able to monitor calls we handle on their behalf. I've got ZapBarge working but I need to restrict the client

Hi everyone, I want to get multiple DDI's and hunting across those DDI's in case one of the lines is busy using analog phone lines. The system is for a large house so I want 3 x PSTN lines. 3 x DDI's and the ability for those DDI's to be presented across all three PSTN lines. BT say you can't have more than one DDI number associated with a PSTN line and that you can't

You should be able to get ISDN though. I think BT provide this anywhere. Otherwise your solution will be a Primary rate (ISDN30) with 8 channels. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Matt Sent: 07 June 2004 10:19 To: asterisk-users@lists.digium.com Subject: Re: RE: [Asterisk-Users] Multiple DDI &

i cannot see caller ID of the call originated from outside zap channel. i hv configured both zapata.conf and extensions.conf. i m right now in india i think asterisk only supports Bellcore enable caller ID. so is it the same bug of BT caller ID problem in UK? or it is the bug of my asterisk configuration? i hv enabled callerID from my TELCO. -------------- next part -------------- An HTML

Hi Folks, First of all, I've been reading a lot and a lot about asterisk and ISDN-BRI, but is really a complicated world, not like PRI or Analog. I have 2 offices with 2 NT boxes and I want to connect them with Asterisk to route outgoing from one office two the other. At the end I want them to look like this Office2 will have only VoIP phones (not ISDN phones connected to a card in asterisk)

I am going to try and use a passive AVM fritz BRI card for my * setup.. Here is the thing.. I need to order my BRI from BT.. The service that looks to be the one to use is what they call ISDN 2e becasue this has the option to setup hunt groups across multiple ISDN2e lines so I could add another line later to get 4 channels.. According to the BT website in order to use the hunt grouping across

Derek, could you give me some details regarding the solar power supply you're using for your installation? Thanks! J?rg > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of > Derek Conniffe > Sent: Thursday, September 15, 2005 12:28 PM > To: Asterisk Users Mailing List -

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

Hello, we had a running configruation where asterisk passed the phone number and the ddi to the pstn (i.e. 595-431) Now only the rootnumber arrives: 5950 I do not know, what to do. I tried to use callingpres (now i am just hiding every number, because 595-0 is no valid extension..) but that did not worked. > Protocol Discriminator: Q.931 (8) len=44 > Call Ref: len= 2 (reference

Hi all, I have one asterisk server with one ISDN BRI connection to PSTN, with h.323 support (oh323) I buy some voip phones, and I connect them to the same switch as asterisk server is; all is at the same TCP network. I need to route some extensions from my DDI (DID) line at asterisk to some voip phones, and also to do: outgoing calls from any voip phone to PSTN via asterisk, and intermediate

Hi folks! Is it possible to tell asterisk not to strip the leading 0 of *incoming* MSNs? I use asterisk with i4l and whenever I get a call from an long-distance party, the leading 0, which should be there according the german numbering, is not. So if I get a call from a mobile phone 0177-1234567 should be displayed, but 177-1234567 is displayed. I double checked if I've forgotten to remove an

Hi, I have one Q: why doesn't work h-extension in macro? I want to setup fax macro, to send tif-file after fax channel hang-up, but h-extension doesn't work in macro, so I must put them to global context. But in this setup, exten => h,1,system(/var/lib/asterisk/bin/mailfax ${FAXFILE} ${EMAILADDR} "${CALLERIDNUM} ${CALLERIDNAME}") mailfax binary will be executed after any

Author: pjha Repository: /hg/zfs-crypto/gate Revision: 1384398963b7f0f86003735b23845a984fe75f5e Log message: 6371650 pci capability ddi iterator Files: create: usr/src/uts/common/io/pci_cap.c create: usr/src/uts/common/sys/pci_cap.h update: usr/src/uts/common/Makefile.files update: usr/src/uts/common/io/pci_intr_lib.c update: usr/src/uts/common/io/pcie.c update:

Hi everybody, I have problems with the chan_capi in the P2P (DDI) mode and it is not possible to use zaphfc, because I need call defelction. This is my capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 language=de ;mode=immediate isdnmode=ptp ; 123456 -0 [interfaces] msn=1234560 incomingmsn=1234560 controller=1

I have * configured with 2 X100P cards (fxs_ks). The lines from the telco are 'analogue both way ddi trunks'. This means that every inbound call contains digits that represent an extension on the PBX. I can make outbound calls from * with no problem however I cannot receive inbound calls on these trunks. Some investigation has shown that when the line is idle there is 50 volts present and

Hi, I'd like to know if and how can I set CallerIDNum for outgoing calls on a PRI line with DDI. Does anyone know if italian Telecom permit this? Thanks -- Domenico Viggiani