similar to: Echo problems using AVM Fritz!PCI Card

Hi All, I'm running asterisk 1.0.7 on debian sarge, and hardware-wise an AVM Fritz!PCI Card, together with chan_capi 0.3.5. The problem is that any inbound/outbound calls on analogue line result in echo on MY end (the asterisk end). I've played with the echo settings in capi.conf (mainly turning on echocancel and echosquelch, also tried playing with rxgain/txgain) to no avail. The only

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

> > That is possible, how could I check that? > > I can see that IRQ 17 is shared between eth0 and my fritz!card > but I > > don't know if it changes anything: > > Can you try it (or eth0) in a different slot (or change IRQ's in the > BIOS if possible) to see if it makes any difference? That's the > only way > to know for sure, anything else is

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

Is case anyone wants to know... The Fritz! USB ISDN box works fine with Asterisk! I'm running CAPI 0.3.0 and love it, because the mini ITX server I have only takes one PCI slot which is now filled with a 4 port Digium card.

Hi All, Has anyone had success with using the AVM Fritz PCI ISDN Card (v2) CAPI drivers with a distro other than suse? The AVM driver is geared towards suse, and after trying them with RedHat 9 I've not got very far. The module compiles but dies when I attempt to modprobe it. I've googled until I almost lost the will to live! What little information I can find seems to refer back to

Hello, I have been wrestling with installing the CAPI drivers for AVM Fritz in order to use chan_capi with Asterisk. I use an SMP machine, RH 9. I have found rpm's for CAPI and AVM drivers (namely: capi4k-utils-2003.06.16-08.mungo.RH9.i686.rpm and kernel-2.4.20-8- avmfcpci-03.11.02-08.mungo.RH9.i686.rpm), but I believe that they support only single processor machines. I've already

Hello everyone! Has anyone had success in configuring the "Fritz!Card DSL" card, a combination of an ISDN adapter and a DSL modem from the german AVM GmbH (http://www.avm.de/) in a dom0 Domain (Xen 2.0.7)? I had success in compiling the modules from http://www.avm.de/de/Download/index.php3 and they load fine with "modprobe fcdsl". But with the Xen dom0 Kernel they seem to

Hello all, I would like to know about the support for this ISDN passive card AVM Fritz-PCI v2.0 with Asterisk: 1. which drive should I use with Asterisk: isdn4linux or capi4linux from AVM (I read some messages on the asterisk-users archives but I didn't find the answer) 2. if the drive is isdn4linux then HiSAX support (for passive cards) is enough ? and the device /dev/ttyI0 (for

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Not strictly Asterisk related, but I'm trying to get an AVM Fritz! card to work with Asterisk on a Fedora Core 3 box. I've grabbed the official AVM Fritz CAPI driver from the AVM website and compiled against the current kernel. However, as soon as I modprobe it I get: CAPI Subsystem Rev 1.1.2.8 fcpci: module license 'Proprietary'

I have a problem trying to install two avm fritz cards on one asterisk machine. I am using fcusb2 driver. 1 card works perfectly. I tried to recompile driver like it is described on this page but with no success. http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO I think the problem is that i can not find this part of code. dev = pci_find_device (AVM_VENDOR_ID, AVM_DEVICE_ID, dev); if

Hello! Is there a way to use AVM Fritz!PCI as a ZAP interface and have it configured for ZAP channels? Thanx in advance! Roland Zagler mailto:r.zagler@fog.at @fog smart partners

hello, does anybody know how to setup avm fritz pci card in p2p mode ? regards marian -- SUNTEQ s. r. o. Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic Tel: +421-46-5430 754 # Fax: +421-46-5439 144 http://www.sunteq.sk/ ------------------------------------------------------------ A mind is like a parachute... it only works when it's open.

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the

hello! I'd like to use my asterisk-box on a p2p-line from my alcatel pbx. isdn4linux and capi works fine on a s0-line from the pbx, but i need more then 8 msns, cause i'd like to implement a voice-mail system and an extension to our "old" pbx with voip-phones. had anyone success using isdn4linux on a t0 (p2p) line (of course with an inexpensive passive card like my avm

Someone have info about install an AVM fritz into FC3 ? I'm getting problems with kernelcapi, after succesfully installed the fcpci support. Thanks -- Adri? Vidal adriavidal@gmail.com Mail is better with 1Gmail

Hi, I have an AVM Fritz! ISDN card connected to an NT1 unit (Australian). I have no problems getting the drivers up and running but when using it with asterisk nothing happens. I call in using a mobile or analogue phone on either of the numbers and the NT1 activity light either flashes or goes solid while ringing but it pauses for a while and on a mobile i get call not answered and a busy

Hello, Is it possible to use * as a gateway in the following setup: LAN (with Windows NT/Linux PCs) | Ethernet (IP) | Linux PC with * and AVM Fritz! ISDN Adapter | ISDN | Someone with a analog/digital phone (POTS) Basically, people sitting on their PCs will wear a headset, and whenever they want to call someone,

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the

Hello Asterisk users, I would like to use 2 BRI lines on my * box but I haven't any PCI slot. Is it to possible to use 2 two AVM Fritz! USB. If not, what other solution can I use? Thanks Amaury