similar to: Zaphfc and BRI problems in Portugal...

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

I've got Zaphfc working running Asterisk v. 0.7.2 Then I have tried with Asterisk V. 1.0 and the latest from CVS - with no succes. Has anybody got zaphfc working with newer version than 0.7.2 ? NR -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040616/32481fca/attachment.htm

Hi Folks, just updated my current Dialplan available on http://capi4linux.thepenguin.de/download/asterisk/config/ It now heavily uses ODBC database (MySQL) to hold most of the data like extensions and incoming connection numbers. An example databasefile is also included. The denylist has also been updated for future and current settings of the german telecom regulator. Again I added many

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

I would like to know how to install asterisk 1.0.9 with zaphfc working on a SuSE 9.2. I tried this: - The rpms with SuSE 9.2 are asterisk 1.0.6 - bristuff works, except for zaphfc, which doesn't compile. - The official asterisk download file doesn't contain isdn bri support Any ideas? Lars Dybdahl.

-----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Zoltan Szecsei Sent: zaterdag 16 juli 2005 12:54 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Multiple ISDN BRI Units with Asterisk usingBristuff zaphfc in NT mode? >> Maybe this is rather a hardware question,

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hi All, what is this? This happens after calling "make loadNT" And I can't do anything with this HFC Card, but the installscript from bri-stuff finished successfully! Aug 17 02:31:42 server kernel: zaphfc: freed one card. Aug 17 02:33:27 server kernel: PCI: Enabling device 00:12.0 (0000 -> 0003) Aug 17 02:33:27 server kernel: PCI: Found IRQ 10 for device 00:12.0 Aug 17 02:33:27

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

Hi there, I just finished work on my current PBX dialplan configuration. I didn't find anything compareable yet so I think it might be interesting for someone else too. Short overview: - seperation of the numbers in blocks (just definded) - error/cause handling - advanced access control (even vor ISDN Zap clients) - access levels - denylist with national number blocks (for Germany) -