similar to: ISDN and incoming MSN

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

I posted a message a little while ago but got no response (that I can recall), I've also seen other people mention this issue. Basically, when you have music on hold, it doesn't play the music on hold, the debug info shows it is starting and then stops straight away.. # My extensions.conf ... exten => s,1,Answer exten => s,2,DigitTimeout,5 exten => s,3,ResponseTimeout,10 exten

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hey All, I'm still (since April) having problems getting RxFax to work over an ISDN4Linux channel. Just wondering if anyone has had any luck getting it to work? I have done a CVS update today (about half hour ago) and made sure I have the latest version of spandsp according to Steve's website (spandsp-0.0.1k). When I was compiling asterisk, I got the following warnings:

Hello everybody, I have a strange comportment with oh323 and asterisk, I'start testing asterisk but with this I can't understant plesae help me ! Thanks Eltorio ---------------------------------------------------------- 1/PB: I can't dial from a H323 extensions (registered on a GNU GK) to a Modem[i4l] line ---------------------------------------------------------- Nothing happens

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hello! Im pretty new of asterisk world: my goal would be using iaxcomm to call ppl over POTN. Yesterday i configured asterisk to be able to hear a song (with Playback() command) with iaxcomm, and it was wonderful. Now, today i tried to configure asterisk to use my ISDN4Linux supported card (a plain HFC card) with asterisk. i configured modem.conf this way, after reading

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

I have asterisk loaded and seemingly working with 4 snom 200 phones. I cannot dial in or out using a DIVA isdn card When I dial out i get "not found xxxxxxx" on the handset. When I dial in i see in /var/log/message isdn_net: Incoming call without OAD, assuming '0' isdn_net: call from 0 -> 0 1856 ignored isdn_tty: Incoming call without OAD, assuming '0' isdn_tty:

Hi all, Here another guy working with ztdummy and having problems with music. MP3Player does not work for me both from a telephone entering through a passive ISDN-adapter as well as a SIP-client in the LAN. Ztdummy works with conferences. Here are my messages. I have seen several discussion threads in the mail-archive regarding this subject, but could not find an answer. Is this something I

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

Hi, I am trying to recice a fax with * using SpanDSP - but it doesn't create the output file. (See the bottom of log file). * Loads both app_rxfax.so and app_txfax.so fine. Also I can't make * autodetect an incomming fax call (yes I have enabled faxdetect=both in zapata.conf - though it's not a Zap device) Any ideas are welcome :-) Best Regards Michael L?jtnant System Details:

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

I'm trying using Asterisk over an isdn line. I configured my Eicon Diva card by the hisax module and it works with the Asterisk's chan_modem (and chan_modem_i4l) driver. The problem is that I can receive calls (on /dev/ttyI0) but when I make a call I always have the line busy (on ttyI0 but even if I use an other device like ttyI1). This is a part of my consol output: --