similar to: H.323 and cause code 'user busy'

Hi, I have asterisk connected to PSTN via H.323 gateway via chan_oh323. Incoming calls to SIP extensions work, but SIP message "486 busy here" from a busy extension isn't correctly forwarded to H.323. As a result, a caller from the H.323 side calling a busy SIP extension gets some rings and then an irritating timeout with H.323 message 'no user responding' instead of

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

Okay, I think I need a sanity check here - If I call a person that's on the phone, I should get a busy signal. Now more specifically, a call comes into the pbx via PRI. The destination dialplan runs busy(20). Now, the PRI causecode should get set to 17 (user busy) so that the originating end can play a busy tone, correct? -Justin -------------- next part -------------- An HTML attachment

I'm trying to build a test suite so that I can run "calls" through and verify the call results. I've made a cross over cable and linked my 2 ISDN30 ports together. So now I can dial out on span 1 , and to receive the call on span 2. in the context for span 2, I have the following: <snip> ; #1 "answer" a call and play music 000XXX : ring for a random period,

hi, well, most of the things work right now due to the help of peter svensson, but after heavy use of our ericsson BP250 today several problems appeared. i split into several mails as they are seperate problems. * i can't signal Busy to the calling party. asterisk receives busy from the ericsson PBX but does not forward this to the external caller. i tried with exten =>

Hello, i have succesfullu setup asterisk with Sangoma E1 card, evrything works well but i don't know how to pass indications from telco switch to the user - when users call bad number telco switch shuld talk "unallocated number" but its only send PRI_CAUSE 1. How to pass voice indications thru asterisk to clients? My /etc/zaptel.conf: span=1,0,0,CCS,HDB3,CRC4 dchan=16

Hi all, I have to asterisk-1.0.9BRIstuffed-0.2.0n boxes each equipped with a TE410P. Box A is connected with pri1 to the PSTN. Box B is connected with pri1 (cpe) to the Box A at pri2 (net). Now I want Box B to dial out to the PSTN tunneled thru Box A and have it get all ISDN indications in case of call failure, eg. unallocated destination number etc. But currently Box B always gets only

Hi all, I am using chan_h323 from Asterisk CVS to interconnect with GNUGK v2.2.2. Then I made call from a H323 EP, thru GNUGK, to SIP EP on Asterisk. However, I only heard ringing when the call was answered on SIP side. Below is the debug from chan_h323. Any help is welcome. Thanks. *CLI> == New H.323 Connection created. -- Setting up Call -- Call token:

Hello, Can such thing be done through dialplan , that say I transfer a call to an extension but it is busy, so that this call returns back to me. Thanks -- Anton Yurchenko<phila@dg.net.ua> Digital Generation

I have hit a problem where chan_h323 sometimes doesn't hang up properly and stays stuck in the "Up" state, with asterisk consuming 100% of CPU: *CLI> show channels Channel (Context Extension Pri ) State Appl. Data H323/ip$127.0.0.1:30008/21552 (local 123 1 ) Up (None) (None) 1 active channel(s) *CLI>

I'm Japanese. Sorry,English is not so understood,Please let me question by items. In Asterisk-1.2.1 and 1.2.2,I cannnot understand the operation of Authenticate application's 'j' option. exten => 123,1,Answer() exten => 123,2,Authenticate(789,j) exten => 123,3,Playback(pin-number-accepted) exten => 123,4,SayDigits(111) exten => 123,103,SayDigits(999) In this

Hi, I'm trying to setup Asterisk to allow users to dial out to the PSTN using a remote box supporting h.323. I'm using chan_h323.so, and I'm able to make outbound calls to a client like netmeeting with a line like this: exten => 242,1,Dial(h323/xxx.xxx.xxx.xxx) And I'm able to receive incoming calls to asterisk. However I'm not sure how to route calls to the remote h.323

hi all I'm trying to setup a dlink dph-100h phone (actually a dph-100m but with the h.323 software) with asterisk and chan_h323. AFACS, the dph-100h software can only be configured to point to a gatekeeper. I know I don't need to do this, but it's a test before I setup my Symbol Netvision phones (I don't have an access point for them now). First, this is what I have, and what

Hi, I want to configure * to use a gatekeeper for routing calls to H.323 endpoints. I imagine it will work like that: * (chan_h323) will query the gatekeeper where to terminate the dialed number and the gatekeeper will return the information for the h.323 gateway. after that chan_h323 will try to make the call to the gateway it has received from the gatekeeper. so instead of duplicating a

Hi, I'm thinking of setting up Asterisk for H.323 video phone clients. Now, what is the difference between native H.323 that come with Asterisk and "Open H.323 for Asterisk" ? TIA Kuni -- Kuniyoshi Murata.........................iChat/AIM:macwebcaster English-Japanese Interpreter mailto:kuni@ej-interpreter.net Macintosh Webcast Specialist

Hi all, I'm a student (my thesis work consist in testing interopearbility SIP/H.323) and I begin to work with asterisk in this days. I have to testing to SIP/H.323, since today I have used Vocal system, but there are some problem for this features. In the asterisk mailing list, in the next message I've seen an e-mail """ [Asterisk-Users] Cisco

> On Sun, 27 Mar 2005, Nenad Radosavljevic wrote: >> Only way I have managed to get Zap channel to reject a call on TE110P >> without answering it, is to dial number that is not handled in dialplan >> (I >> have a ISDN PRI with 100 number DID service, and about 30 of them are >> handled by dialplan). So far I didn't manage to reject call that are >>

Hello, I have just ran nmap on a remote server with a minimal (or so I believed) Centos 4.3 installation. Besides what I expected (ssh, httpd, smtp) it found as open for listening these ports: Starting Nmap 3.95 ( http://www.insecure.org/nmap/ ) at 2006-06-14 17:57 CEST Interesting ports on <my.remote.server> (The 1667 ports scanned but not shown below are in state: closed) PORT STATE

I'm new to H.323 and I have noticed that there are two separate channel drivers for * available - the inbuilt one, and oh-323. I had trouble compiling oh-323 with the current cvs stable, so I tried the inbiult one (with specifiec recommended versions of openh323 and pwlib). It compiled cleanly but I am told that it is not recommended (unstable?). Can someone with first-hand * H.323

Hi Michael and Everyone I'm trying to connect Asterisk to a CISCO AS5350 using oh323 and I'm getting this error "reason 24 (Call ended with Q.931 cause)" I've checked the Asterisk wiki and several other resources. Please can anyone give me a hint on what the problem is I reach my wits end. Thanks Tola my config and debug Configuration of OpenH323 channel driver