similar to: tieline digit timeout

I am trying to configure MeetMe so that external callers can enter the conference rooms after an IVR menu. I have created Conf rooms for all internal Ext's with a prefix of 8. When I call into the system from my vonage trunck the IVR picks up but will not let me dial a conf room. It tells me it is a invalid extension. Can anyone help with a sample conf on this? Thanks, RC

I have an nec electra elite 192 with a t1 card; and am looking for suggestions as to integrating them (can't throw out the system yet!). I have a fully working asterisk server -CVS-04/27/04-19:01:05- (found a hp d220 for $350.00!), 2 digium t100p cards, a plain t1 with loopstart signaling, and 2 working bt102 grandstream ip phones (thanks again Matt for your "start from scratch"

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

I'm getting down to the last of my * issues ... After calling a bank, or cc processing center; you have to enter your social security number, or the cc number - followed by the # key. The lovely * voice responds "transfering" I'm sorry that was an invalade selection. Sometimes the IVR on the other end still gets the digits and proceeds; other times it breaks the IVR on the

Hi, I just setup a box with RH 9, and latest asterisk via CVS. The box as a T100P card in it that is currently hooked up to nothing. I did have the sample configs in place via make samples, and the only change I made was to add an entry to sip.conf for my Cisco 7960. When I dial 1000 to get to the main greeting I hear nothing, though the command line output looks fine to me. Any ideas? --

OK, I think I'm ready for the next step from the X100P. Splitting a T1 with a T100P and a channel bank/s ~ 50 extensions. I think the existing system uses NEC phones for ~34 extensions, I don't know the specific model yet of the phones or the channel bank. If the channel bank is not compatible with Asterisk/digium what brand should I be looking at to interface best with Asterisk and

Hello all- So I have * up and running and connected to a legacy system via em_w lines and have no trouble dialing from * through the tie line but from the PBX across the tie line I am having intermittant receipt of the DTMF. T-Berd testing is showing that the digits are coming across but * is either missing the first digit consistantly. This seems to me to have something to do with start timers

Hello, everyone, I am currently trying to get the asterisk server to talk with a 3COM NBX with T1 connection. My asterisk server has a T100p, TDM20B, a couple of sip phones. Now the sip phones are calling 3COM NBX phones fine, however, the analog phone has problem when dialing the NBX phones. The connection is established and the NBX auto-attendant picks up the call however the NBX end says that

I see there is the DigitTimeout application that sets the maximum time between digits before asterisk will interpet. Is there any way to control the minimum? We are having problems with incoming calls on our X100P where callers try to dial 10, but the 1 gets detected twice and they end up on extension 11. Thanks Mark Farver

I'm trying to get a Carrier Access Corp. Channel Bank I working with a Digium T100P without success. What is stranger is that the status lights on the channel bank and T100P seem to change almost each time I power cycle the channel bank or reset the T100P. The channel bank has three status lights: T1, Framing, Status. T1 is green, Status is yellow, and Framing is usually red but sometime

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

OK, this is probably a dumb question for a lot of you, but I have no experience with digital lines outside of a tiny bit of ISDN, so I'll just bite the bullet and ask some newbie questions. I am attempting to plan an asterisk installation with about 20 SIP phones and the following incoming lines: 1) At least 6 (as many as 10) lines for voice to the SIP phones 2) 2 incoming/outgoing fax 3)

Hi, I'm am currently in the process of trying to integrate an * box with an NEC Electra Elite IPK. Currently, we have 7 POTS lines coming into our building. These lines are plugged into our NEC using the appropriate analog line interface card from NEC. The NEC effectively has NO configuration done to it, other than to make all the internal phones ring when a call comes in. We also

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Hello, Does anybody know of a place to get a half-height PCI slot bracket for the Digium T100P card? I have an application to fit them in 1U cases for small, deployable PBX's. The T100P itself is short enough to fit in a half-height slot but I need an appropriate mounting bracket to screw it into the case. Thanks, Mark Hagler

Hi 2 all. I've a nice issue my * system. I have: asterisk latest cvs T100P + Zhone cb (3fxo+10fxs used) Diva Server 4BRI running Capi a bunch of pots and sip phones The whole system is running good (thanks to capigod and Bic. for the help with the Eicon Diva), but there's a very strange issue when calls arrive on the Diva and then bridged to the pots on the channel bank: the voice is not